In this study, we present a novel composite material based on commercially available polyurethane foams functionalized with colloidal superparamagnetic iron oxide nanoparticles and submicrometer polytetrafluoroethylene particles, which can efficiently separate oil from water. Untreated foam surfaces are inherently hydrophobic and oleophobic, but they can be rendered water-repellent and oil-absorbing by a solvent-free, electrostatic polytetrafluoroethylene particle deposition technique. It was found that combined functionalization of the polytetrafluoroethylene-treated foam surfaces with colloidal iron oxide nanoparticles significantly increases the speed of oil absorption. Detailed microscopic and wettability studies reveal that the combined effects of the surface morphology and of the chemistry of the functionalized foams greatly affect the oil-absorption dynamics. In particular, nanoparticle capping molecules are found to play a major role in this mechanism. In addition to the water-repellent and oil-absorbing capabilities, the functionalized foams exhibit also magnetic responsivity. Finally, due to their light weight, they float easily on water. Hence, by simply moving them around oil-polluted waters using a magnet, they can absorb the floating oil from the polluted regions, thereby purifying the water underneath. This low-cost process can easily be scaled up to clean large-area oil spills in water.

The authors report on ambipolar organic transistors based on the soluble dithiolene derivative ͑diphenylethylenedithiolato͒͑1,3-dithiol-2-thione-4,5-dithiolato͒nickel ͓Ni͑dpedt͒͑dmit͔͒. Due to its small band gap, efficient injection of holes and electrons from gold source/drain electrodes is possible. Both carrier mobilities are estimated to be approximately equal with maximum value on the order of 10 −4 cm 2 / V s. The transistors exhibit excellent ambient stability with a shelve lifetime exceeding 3 months. The pronounced stability of Ni͑dpedt͒͑dmit͒ as well as of several other molecules studied here is correlated to their redox potential. The present findings can be used as a general guide towards design and synthesis of air-stable ambipolar/n-channel molecules.

We have studied in vitro toxicity of iron oxide nanoparticles (NPs) coated with a thin silica shell (Fe3O4/SiO2 NPs) on A549 and HeLa cells. We compared bare and surface passivated Fe3O4/SiO2 NPs to evaluate the effects of the coating on the particle stability and toxicity. NPs cytotoxicity was investigated by cell viability, membrane integrity, mitochondrial membrane potential (MMP), reactive oxygen species (ROS) assays, and their genotoxicity by comet assay. Our results show that NPs surface passivation reduces the oxidative stress and alteration of iron homeostasis and, consequently, the overall toxicity, despite bare and passivated NPs show similar cell internalization efficiency. We found that the higher toxicity of bare NPs is due to their stronger in-situ degradation, with larger intracellular release of iron ions, as compared to surface passivated NPs. Our results indicate that surface engineering of Fe3O4/SiO2 NPs plays a key role in improving particles stability in biological environments reducing both cytotoxic and genotoxic effects.

Magnetic hyperthermia (MH) based on magnetic nanoparticles (MNPs) is a promising adjuvant therapy for cancer treatment. Particle clustering leading to complex magnetic interactions affects the heat generated by MNPs during MH. The heat efficiencies, theoretically predicted, are still poorly understood because of a lack of control of the fabrication of such clusters with defined geometries and thus their functionality. This study aims to correlate the heating efficiency under MH of individually coated iron oxide nanocubes (IONCs) versus soft colloidal nanoclusters made of small groupings of nanocubes arranged in different geometries. The controlled clustering of alkyl-stabilized IONCs is achieved here during the water transfer procedure by tuning the fraction of the amphiphilic copolymer, poly(styrene-co-maleic anhydride) cumene-terminated, to the nanoparticle surface. It is found that increasing the polymer-to-nanoparticle surface ratio leads to the formation of increasingly large nanoclusters with defined geometries. When compared to the individual nanocubes, we show here that controlled grouping of nanoparticles—so-called “dimers” and “trimers” composed of two and three nanocubes, respectively—increases specific absorption rate (SAR) values, while conversely, forming centrosymmetric clusters having more than four nanocubes leads to lower SAR values. Magnetization measurements and Monte Carlo-based simulations support the observed SAR trend and reveal the importance of the dipolar interaction effect and its dependence on the details of the particle arrangements within the different clusters.

Here, we propose the use of magnetic hyperthermia as a means to trigger the oxidation of Fe1−xO/Fe3−δO4 core-shell nanocubes to Fe3−δO4 phase. As a first relevant consequence, the specific absorption rate (SAR) of the initial core-shell nanocubes doubles after exposure to 25 cycles of alternating magnetic field stimulation. The improved SAR value was attributed to a gradual transformation of the Fe1−xO core to Fe3−δO4, as evidenced by structural analysis including high resolution electron microscopy and Rietveld analysis of X-ray diffraction patterns. The magnetically oxidized nanocubes, having large and coherent Fe3−δO4 domains, reveal high saturation magnetization and behave superparamagnetically at room temperature. In comparison, the treatment of the same starting core-shell nanocubes by commonly used thermal annealing process renders a transformation to γ-Fe2O3. In contrast to other thermal annealing processes, the method here presented has the advantage of promoting the oxidation at a macroscopic temperature below 37 °C. Using this soft oxidation process, we demonstrate that biotin-functionalized core-shell nanocubes can undergo a mild self-oxidation transformation without losing their functional molecular binding activity.

Water wetting and adhesion control on polymeric patterns are achieved by tuning the configuration of their surface's structural characteristics from single to dual and triple length-scale. In particular, surfaces with combined micro-, submicrometer-,and nanoroughness are developed, using photolithographically structured SU-8 micro-pillars as substrates for the consecutive spray deposition of polytetrafluoroethylene (PTFE) submicrometer particles and hydrophobically capped iron oxide colloidal nanoparticles. The PTFE particles alone or in combination with the nanoparticles render the SU-8 micropillars superhydrophobic. The water adhesion behaviour of the sprayed pillars is more complex since they can be tuned gradually from totally adhesive to completely non adhesive. The influence of the hierarchical geometrical features of the functionalized surfaces on this behaviour is discussed within the frame of the theory. Specially designed surfaces using the described technique are presented for selective drop deposition and evaporation. This simple method for liquid adhesion control on superhydrophobic surfaces can find various applications in the field of microfluidics, sensors, biotechnology, antifouling materials, etc.

No abstract

Organic-inorganic hybrid compounds based on lead halide units of the formula (CH 3 NH 3 ) 2 -(CH 3 C 6 H 4 CH 2 NH 3 ) 2 Pb 3 (Br x Y 1−x ) 10 (Y = Cl, I) were prepared from melts, and their optical absorption as well as photoluminescence spectra, before and after grinding the compounds, were investigated. The luminescence of the materials after grinding is strong and is observed with naked eye. By changing the mole fraction (x), the strong photoluminescence in the range from ca. 400 nm to ca. 600 nm could be tuned. These effects indicate that the hybrid compounds are promising materials for potential applications.