Abstract-A key challenge to the future of energy-harvesting systems is the discontinuous power supply that is often generated. We propose a new approach, Hibernus, which enables computation to be sustained during intermittent supply. The approach has a low energy and time overhead which is achieved by reactively hibernating: saving system state only once, when power is about to be lost, and then sleeping until the supply recovers. We validate the approach experimentally on a processor with FRAM nonvolatile memory, allowing it to reactively hibernate using only energy stored in its decoupling capacitance. When compared to a recently proposed technique, the approach reduces processor time and energy overheads by 76-100% and 49-79% respectively.
Abstract-Energy harvesters are being used to power autonomous systems, but their output power is variable and intermittent. To sustain computation, these systems integrate batteries or supercapacitors to smooth out rapid changes in harvester output. Energy storage devices require time for charging and increase the size, mass and cost of systems. The field of transient computing moves away from this approach, by powering the system directly from the harvester output. To prevent an application from having to restart computation after a power outage, approaches such as Hibernus allow these systems to hibernate when supply failure is imminent. When the supply reaches the operating threshold, the last saved state is restored and the operation is continued from the point it was interrupted. This work proposes Hibernus++ to intelligently adapt the hibernate and restore thresholds in response to source dynamics and system load properties. Specifically, capabilities are built into the system to autonomously characterize the hardware platform and its performance during hibernation in order to set the hibernation threshold at a point which minimizes wasted energy and maximizes computation time. Similarly, the system auto-calibrates the restore threshold depending on the balance of energy supply and consumption in order to maximize computation time. Hibernus++ is validated both theoretically and experimentally on microcontroller hardware using both synthesized and real energy harvesters. Results show that Hibernus++ provides an average 16% reduction in energy consumption and an improvement of 17% in application execution time over stateof-the-art approaches.
Abstract-Modern mobile and embedded devices are required to be increasingly energy-efficient while running more sophisticated tasks, causing the CPU design to become more complex and employ more energy-saving techniques. This has created a greater need for fast and accurate power estimation frameworks for both run-time CPU energy management and design-space exploration. We present a statistically rigorous and novel methodology for building accurate run-time power models using Performance Monitoring Counters (PMCs) for mobile and embedded devices, and demonstrate how our models make more efficient use of limited training data and better adapt to unseen scenarios by uniquely considering stability. Our robust model formulation reduces multicollinearity, allows separation of static and dynamic power, and allows a 100× reduction in experiment time while sacrificing only 0.6% accuracy. We present a statistically detailed evaluation of our model, highlighting and addressing the problem of heteroscedasticity in power modeling. We present software implementing our methodology and build power models for ARM Cortex-A7 and Cortex-A15 CPUs, with 3.8% and 2.8% average error, respectively. We model the behavior of the nonideal CPU voltage regulator under dynamic CPU activity to improve modeling accuracy by up to 5.5% in situations where the voltage cannot be measured. To address the lack of research utilizing PMC data from real mobile devices, we also present our data acquisition method and experimental platform software. We support this work with online resources including software tools, documentation, raw data and further results.
The technology and healthcare industries have been deeply intertwined for quite some time. New opportunities, however, are now arising as a result of fast-paced expansion in the areas of the Internet of Things (IoT) and Big Data. In addition, as people across the globe have begun to adopt wearable biosensors, new applications for individualized eHealth and mHealth technologies have emerged. The upsides of these technologies are clear: they are highly available, easily accessible, and simple to personalize; additionally they make it easy for providers to deliver individualized content cost-effectively, at scale. At the same time, a number of hurdles currently stand in the way of truly reliable, adaptive, safe and efficient personal healthcare devices. Major technological milestones will need to be reached in order to address and overcome those hurdles; and that will require closer collaboration between hardware and software developers and medical personnel such as physicians, nurses, and healthcare workers. The purpose of this special issue is to analyze the top concerns in IoT technologies that pertain to smart sensors for health care applications; particularly applications targeted at individualized tele-health interventions with the goal of enabling healthier ways of life. These applications include wearable and body sensors, advanced pervasive healthcare systems, and the Big Data analytics required to inform these devices.
The thermal profile of multicore systems vary both within an application's execution (intra) and also when the system switches from one application to another (inter). In this paper, we propose an adaptive thermal management approach to improve the lifetime reliability of multicore systems by considering both inter-and intra-application thermal variations. Fundamental to this approach is a reinforcement learning algorithm, which learns the relationship between the mapping of threads to cores, the frequency of a core and its temperature (sampled from on-board thermal sensors). Action is provided by overriding the operating system's mapping decisions using affinity masks and dynamically changing CPU frequency using in-kernel governors. Lifetime improvement is achieved by controlling not only the peak and average temperatures but also thermal cycling, which is an emerging wear-out concern in modern systems. The proposed approach is validated experimentally using an Intel quad-core platform executing a diverse set of multimedia benchmarks. Results demonstrate that the proposed approach minimizes average temperature, peak temperature and thermal cycling, improving the mean-timeto-failure (MTTF) by an average of 2x for intra-application and 3x for inter-application scenarios when compared to existing thermal management techniques. Furthermore, the dynamic and static energy consumption are also reduced by an average 10% and 11% respectively.
Abstract-Heterogeneous multi-core platforms that contain different types of cores, organized as clusters, are emerging, e.g. ARM's big.LITTLE architecture. These platforms often need to deal with multiple applications, having different performance requirements, executing concurrently. This leads to generation of varying and mixed workloads (e.g. compute and memory intensive) due to resource sharing. Run-time management is required for adapting to such performance requirements and workload variabilities and to achieve energy efficiency. Moreover, the management becomes challenging when the applications are multi-threaded and the heterogeneity needs to be exploited. The existing run-time management approaches do not efficiently exploit cores situated in different clusters simultaneously (referred to as inter-cluster exploitation) and DVFS potential of cores, which is the aim of this paper. Such exploitation might help to satisfy the performance requirement while achieving energy savings at the same time. Therefore, in this paper, we propose a run-time management approach that first selects thread-to-core mapping based on the performance requirements and resource availability. Then, it applies online adaptation by adjusting the voltage-frequency (V-f) levels to achieve energy optimization, without trading-off application performance. For thread-to-core mapping, offline profiled results are used, which contain performance and energy characteristics of applications when executed on the heterogeneous platform by using different types of cores in various possible combinations. For an application, thread-to-core mapping process defines the number of used cores and their type, which are situated in different clusters. The online adaptation process classifies the inherent workload characteristics of concurrently executing applications, incurring a lower overhead than existing learning-based approaches as demonstrated in this paper. The classification of workload is performed using the metric Memory Reads Per Instruction (MRPI). The adaptation process pro-actively selects an appropriate V-f pair for a predicted workload. Subsequently, it monitors the workload prediction error and performance loss, quantified by instructions per second (IPS), and adjusts the chosen V-f to compensate. We validate the proposed run-time management approach on a hardware platform, the Odroid-XU3, with various combinations of multi-threaded applications from PARSEC and SPLASH benchmarks. Results show an average improvement in energy efficiency up to 33% compared to existing approaches while meeting the performance requirements.
Abstract-Energy harvesting allows low-power embedded devices to be powered from naturally-ocurring or unwanted environmental energy (e.g. light, vibration, or temperature difference). While a number of systems incorporating energy harvesters are now available commercially, they are specific to certain types of energy source. Energy availability can be a temporal as well as spatial effect. To address this issue, 'hybrid' energy harvesting systems combine multiple harvesters on the same platform, but the design of these systems is not straightforward. This paper surveys their design, including trade-offs affecting their efficiency, applicability, and ease of deployment. This survey, and the taxonomy of multi-source energy harvesting systems that it presents, will be of benefit to designers of future systems. Furthermore, we identify and comment upon the current and future research directions in this field.
Abstract-The challenge of improving water quality is a growing global concern, typified by the European Commission Water Framework Directive and the United States Clean Water Act. The main drivers of poor water quality are economics, poor water management, agricultural practices and urban development. This paper reviews the extensive role of non-point sources, in particular the outdated agricultural practices, with respect to nutrient and contaminant contributions. Water quality monitoring (WQM) is currently undertaken through a number of data acquisition methods from grab sampling to satellite based remote sensing of water bodies. Based on the surveyed sampling methods and their numerous limitations, it is proposed that wireless sensor networks (WSNs), despite their own limitations, are still very attractive and effective for real-time spatio-temporal data collection for WQM applications. WSNs have been employed for WQM of surface and ground water and catchments, and have been fundamental in advancing the knowledge of contaminants trends through their high resolution observations. However, these applications have yet to explore the implementation and impact of this technology for management and control decisions, to minimize and prevent individual stakeholder's contributions, in an autonomous and dynamic manner. Here, the potential of WSN-controlled agricultural activities and different environmental compartments for integrated water quality management is presented and limitations of WSN in agriculture and WQM are identified. Finally, a case for collaborative networks at catchment scale is proposed for enabling cooperation among individually networked activities/stakeholders (farming activities, water bodies) for integrated water quality monitoring, control and management.Index Terms-wireless sensor networks, agricultural activities, water quality monitoring and management, catchment, collaborative. INTRODUCTIONWater is a key natural resource which is vital for the survival of all ecosystems on the planet. However, less than 1% of the earth's water resources are accessible to humans as fresh water, in the form of either surface or ground water (Krchnak et al., 2002, UNESCO, 2006. Although there is currently sufficient water for essential activities (Blanco et al., 2009) including drinking, irrigation, and domestic and industrial use on a global scale, the spatial distribution of water suggests that, in many cases, it is not available where it is required. Because of the unequal distribution of fresh water resources, billions of people around the globe live in water-stressed and water-limited environments. Therefore it is crucial to preserve water resources although in practice it is continually degraded and depleted owing to inappropriately targeted funding initiatives leading to poor water management, redundant and outdated agricultural practices and urban development (Rosegrant et al., 2002, Verhoeven et al., 2006. The key issues relating to global freshwater quality problems in the environment and public hea...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
334 Leonard St
Brooklyn, NY 11211
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.