Weld-Line in an injection molded part develops when two or more melt fronts are converged together. The weld-line is unavoidable when the design is complex where two melt flow fronts are mating each other head-to-head, this mating area is mechanically weak compared to other portions of the modeled part. The decrease in strength in the weld-line area can be attributed to several factors like molecular diffusion, fiber orientation effect, unoptimized process conditions, surface tension effect, internal residual stresses, etc. The strength of the weld-line area can be increased by optimizing injection molding process parameters like melt temperature, injection speed, packing pressure, changing gate type and location, etc. The present work focuses on studying the effect of packing pressure on strength of stagnation weld-line. This has been examined with experimental testing and scanning electron micrographs of the fractured surface on the weld-line and without weld-line specimens. The special injection mold is designed and fabricated to produce plaques having stagnation weld-line. The plaques are prepared out of 30% glass-filled Polyamide 6 material. The four sets of plaques are produced by changing the magnitude of packing pressure equal to 60% of filling pressure, with increment of 20% up to 120% of filling pressure. The tensile test specimens are machined on these plaques for two different angular orientations and testing is conducted as per ISO 527-2. The results demonstrated that, without weld-line specimens, the tensile modulus, stress at break marginally increases with an increase in packing pressure, and strain at break decreases with an increase in packing pressure. However, for specimens with stagnation weld-lines, both the tensile modulus and stress at break are observed to be 42% of without weld-lines samples for minimum packing pressure. The results obtained are evident from stress-strain graphs and scanning electron micrographs.
In an injection molding process, a weld-line forms when two flow fronts meet each other. Weld-line is a weak area which reduces the strength of the part locally. For multiple gate and complex part, molding weld-lines are unavoidable, therefore mechanical behavior of the weld-line needs to be predicted. This paper presents the effect of weld-lines on tensile properties of glass fibers reinforced polyamide-6 composite. An injection molding plaque tool has been designed and manufactured with the inputs from mold flow simulation software. The gating system is designed in such a way that the angle between two flow fronts is as minimum as possible, which theoretically gives the lowest strength at weld locations. The plaques are manufactured with BASF material Ultramid B3WG6 grade (glass filled 30%) which is a widely used engineering plastic material. Test specimens have been cut on a plaque for various angular positions. Experimental evaluation for tensile testing, tensile modulus, and stressstrain behavior for specimens with and without weld-line at different angular positions was evaluated as per ISO 527-2 standards. It has been established that the weld line significantly influences the tensile properties of the part. The presence of a weld line results in a significant decrease in the tensile strength of the part. Experimental results show approximately 58% reduction in tensile modulus and 49% reduction in stress at break values in specimen with weld-lines as compared to specimen without weld-lines.
The injection molding process is widely accepted for the processing of engineering thermoplastics due to the ease of manufacturing complex designs. Weld‐line is a defect occurring in injection molded parts when two flow fronts join each other. At weld‐line locations, parts exhibit lower mechanical strength mainly due to inadequate intermolecular diffusion and fiber orientation anisotropy. The present work is aimed at investigating and comparing weld‐line strength for unfilled and glass‐filled polyamide‐6 materials. To achieve this, polyamide‐6 unfilled, 30% glass‐filled, and 50% glass‐filled materials are used to manufacture plaques. The special‐purpose mold is designed to obtain plaques with and without weld‐lines with help of Moldflow simulations. The specimens for tensile tests are then cut from molded plaques and experimental testing is conducted to evaluate tensile properties. Fractured surfaces of specimens are examined using a scanning electron microscope. The results demonstrated a significant drop in tensile strength and modulus for glass‐filled material weld‐line specimens when compared to specimens of no weld‐line. However, for unfilled specimens, tensile strength and modulus are almost the same for samples with and without weld‐line. A reduction in tensile strength of 13%, 49%, and 57% is observed for unfilled, 30% glass‐filled, and 50% glass‐filled polyamide‐6 material respectively.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.