No abstract

The design of meshes for the treatment of incisional hernias could benefit from better knowledge of the mechanical response of the abdominal wall and how this response is affected by the implant. The aim of this study was to characterise the mechanical behaviour of the human abdominal wall. Abdominal walls were tested ex vivo in three states: intact, after creation of a defect simulating an incisional hernia, and after reparation with a mesh implanted intraperitonally. For each state, the abdominal wall was subjected to air pressure loading. Local strain fields were determined using digital image correlation techniques. The strain fields on the internal and external surfaces of the abdominal wall exhibited different patterns. The strain patterns on the internal surface appeared to be related to the underlying anatomy of the abdominal wall. Higher strains were observed along the linea alba than along the perpendicular direction. Under pressure loading, the created incision increased the strain of the abdominal wall compared to the intact state in 5 cases of a total 6. In addition, the mesh repair decreased the strains of the abdominal wall compared to the incised state in 4 cases of 6. These results suggest that the intraperitoneal mesh restores at least partially the mechanical behaviour of the wall and provides quantification of the effects on the strains in various regions.

Increase of the defect size and decrease of the overlap affected significantly the VHR mechanical performances. Such numerical models could help to better understand the behavior of the repaired abdominal wall and finally to reduce the clinical complications.

PurposeIncisional hernia remains a frequent complication after abdominal surgery associated with significant morbidity and high costs. Animal and clinical studies have exhibited some limitations. The purpose of this study was to develop an artificial human abdominal wall (AW) simulator in order to enable investigations on closure modalities. We hypothesized that a physical model of the human AW would give new insight into commonly used suture techniques representing a substantial complement or alternative to clinical and animal studies.MethodsThe ‘AbdoMAN’ was developed to simulate human AW biomechanics. The ‘AbdoMAN’ capacities include measurement and regulation of intra-abdominal pressure (IAP), generation of IAP peaks as a result of muscle contraction and measurements of AW strain patterns analyzed with 3D image stereo correlation software. Intact synthetic samples were used to test repeatability. A laparotomy closure was then performed on five samples to analyze strain patterns.ResultsThe ‘AbdoMAN’ was capable of simulating physiological conditions. AbdoMAN lateral muscles contract at 660 N, leading the IAP to increase up to 74.9 mmHg (range 65.3–88.3). Two strain criteria were used to assess test repeatability. A test with laparotomy closure demonstrated closure testing repeatability.ConclusionsThe ‘AbdoMAN’ reveals as a promising enabling tool for investigating AW surgery-related biomechanics and could become an alternative to animal and clinical studies. 3D image correlation analysis should bring new insights on laparotomy closure research. The next step will consist in evaluating different closure modalities on synthetic, porcine and human AW.Electronic supplementary materialThe online version of this article (doi:10.1007/s10029-017-1615-x) contains supplementary material, which is available to authorized users.

Interface conditions are of prime importance for implant fixation in the early post-operative period and modelling of specific biochemical interactions at implant surface is still missing. We hypothesized that updating osteoblast adhesion properties and growth factor source in an active zone located at the implant surface was relevant to model biochemical interactions of implant with its environment. We proposed an innovative set of diffusive-convective-reactive equations which relevant parameters were the cell decay factor, the cell motility and the growth factor balance. Initial comparison with histomorphometic results from a stable PMMA canine implant model provided an encouraging base to implement a numerical sensitivity analysis to evaluate the role of three types of bioactive surfaces: acid-etched titanium, coarse grit-blasted acid-etched titanium and coarse grit-blasted acid-etched titanium with RGDS peptide. We found that cell diffusion decrease (acid-etched+RGDS peptide vs. PMMA), and increase of local growth factor fraction (PMMA vs. acid-etched+RGDS peptide), significantly improved the amount of mineralized tissue on the implant surface. When the variation of structural fraction to cell motility and growth factor synthesis was investigated, an envelope pattern with an optimum was obtained but this could be exceeded for strong surface modifications and/or for high growth factor concentrations. The model also confirmed that implant bioactive properties should play a limited role to reduce heterogeneity of new-formed tissue. In conclusion, we suggested that our innovative theoretical approach was relevant to investigate implant fixation and could potentially help in reduction of implant revision.