Effects of the incorporation of Cr, Ni, Co, Ag, Al, Ni and Pt cations in titanate nanotubes (NTs) were examined on the NOx conversion. The structural and morphological characterizations evidenced that the ion-exchange reaction of Cr, Co, Ni and Al ions with the NTs produced catalysts with metals included in the interlayer regions of the trititanate NTs whereas an assembly of Ag and Pt nanoparticles were either on the nanotubes surface or inner diameters through an impregnation process. Understanding the role of the different metal cations intercalated or supported on the nanotubes, the optimal selective catalytic reduction of NOx by CO reaction (SCR) conditions was investigated by carrying out variations in the reaction temperature, SO2 and H2O poisoning and long-term stability runs. Pt nanoparticles on the NTs exhibited superior activity compared to the Cr, Co and Al intercalated in the nanotubes and even to the Ag and Ni counterparts. Resistance against SO2 poisoning was low on NiNT due to the trititanate phase transformation into TiO2 and also to sulfur deposits on Ni sites. However, the interaction between Pt2+ from PtOx and Ti4+ in the NTs favored the adsorption of both NOx and CO enhancing the catalytic performance.

The effects of the metal incorporation into hydroxyapatites on the deactivation behavior of the solids were examined in the esterification of glycerol (EG) reaction. The introduction of Cu, Co, or Ni ions by ion exchange in calcium-deficient hydroxyapatites resulted in active catalysts for the EG reaction. The metal contents were varied from 2.0 to 17.0%, providing better performances at rather high metal contents. Part of metal species existed in the hydroxyapatite lattice structure and also as isolated Cu2+, Ni2+, and Co2+ entities on the surface, as shown by XPS and EPR. The effects of the reaction temperature, reaction time, and glycerol to acetic acid molar ratios were deeply investigated. The spent solids used in this study were characterized by XRD, FTIR, SEM-EDS, chemical analyses, EPR, and XPS. The Cu2+–OH acid pairs could promote a superior catalytic performance of Cu-containing hydroxyapatites due to the resistance of these solids against leaching of the active species, which is even better than those of Co and Ni-containing counterparts with high metal contents. Cu into hydroxyapatite had a good reusability and long-term utilization for five consecutive cycles of 24 h under a glycerol to acetic acid molar ratio of 0.25 at 80 °C, and longer reaction times provide triacetin formation. This was due to the fact that Cu was stabilized by interacting with Ca, PO4, and OH sites into the hydroxyapatite lattice, being highly active for the EG reaction. The results also revealed that isolated Cu2+ sites played an important role in enhancing the glycerol conversion, intrinsically due to the Cu-containing hydroxyapatites ability to avoid strong adsorption of glycerol oligomers on the catalytic sites.

A facile strategy for the design of porous supports was obtained by modifying the sol-gel method followed by the wet impregnation technique. In this respect, herein, the acidity of the γ-Al2O3 phase was modulated by adding basic MgO, La2O3 or ZnO promoters to form binary supported catalysts. The Ni and Co dispersion on the supports associated with their tunable acidity and morphologies resulted in highly porous supported alumina-based catalysts. The physicochemical properties of the solids were comprehensively investigated by XRD, textural properties, Raman and FTIR spectroscopy, SEM-EDS, TEM, EPR and XPS analyses. The catalytic performances in the esterification of glycerol in the presence of acetic acid (EG) for the acetins production were evaluated. The highly dispersed NiO and Co3O4 active species on binary porous supports produced synergistic effects appearing to be the reason for the activity of the solids in the EG reaction. Under the optimized reaction conditions, NiCo/MgO-Al2O3 was found to be a robust solid with superior catalytic performance and improved stability in four reaction cycles with 65.0% of glycerol conversion with an exclusive selectivity of 53% for triacetin. The presence of Co2+/Co3+ and Ni2+ strongly interacting with the spinel γ-Al2O3 and MgAl2O4 phases, the latter having a large number of lattice oxygen species, was considered another active component besides those of Ni and Co in the esterification of glycerol.

In the original publication, there was a mistake in Figure 1 as published [...]