We wished to compile a data set of results from the experimental literature to support the development and validation of accurate computational models (force fields) for an important class of micelle-forming nonionic surfactant compounds, the poly(ethylene oxide) alkyl ethers, usually denoted C n E m . However, careful examination of the experimental literature exposed a striking degree of variation in values reported for critical micelle concentrations (cmc) and mean aggregation numbers (N agg ). This variation was so large that it masked important trends known to exist within this family of molecules, thereby rendering most of the literature data to be of limited utility for force field development. In this work, we describe some reasons for the wide variability in the experimental literature, and we present a set of cmc and aggregation number data for 12 C n E m compounds that we feel is appropriate to use for the construction of and validation of computational models. The cmc values we selected are from the existing experimental literature and represent a carefully chosen and consistent subset that conveys important trends seen by many of the experimental studies. However, for a corresponding and consistent set of weight-averaged aggregation numbers, we needed to perform new dynamic light scattering (DLS) experiments. The results of these experiments were carefully analyzed to obtain not just mean aggregation numbers but also the underlying micelle size distribution functions. Several trends observed in the cmc and N agg observables are highlighted and serve as challenges for developers of force field and simulation methodology. The analysis of the DLS experiments accounts for the fact that a broad distribution of micelle sizes exists for many of these compounds and that one must be careful to use the appropriate weighted averages (e.g., mass-weighted vs number-weighted averages) in comparing results from different types of experiments and in comparing results from experiments with those from simulations.

LiNi0.5Mn1.5O4 epitomizes the challenges imposed by high electrochemical potential reactivity on the durability of high energy density Li-ion batteries. Postsynthesis coatings have been explored as a solution to these challenges, but the fundamentals of their function have not been ascertained. To contribute to this understanding, the surface of LiNi0.5Mn1.5O4 microparticles was modified with Mg2+, a coating component of literature relevance, using two different heat treatment temperatures, 500 and 800 °C. A combination of characterization tools revealed that Mg2+ was introduced mainly as an inhomogeneous MgO coating in the sample treated at 500 °C, and into the spinel lattice at the subsurface of the particles at 800 °C. Comparing the properties of these two different materials with an unmodified baseline afforded the opportunity to evaluate the effect of varying surface chemistries. Coulometry in Li metal half cells was used as a macroscopic measure of side reactions at the electrode–electrolyte interfaces. This magnitude was comparable in all the materials at room temperature. In contrast, a significant drop in efficiency was observed in the untreated material when the cycling temperature was raised to 50 °C, but not in the modified materials. The origin of the reduced reactivity of the materials after introducing Mg-based modifications was evaluated by probing the chemical changes at the Ni–O bonds using soft XAS. Taken together, the results of this study revealed that incorporation of Mg stabilizes highly oxidized Ni–O species, which can be related to the better stability toward the electrolyte. They point to a pathway toward the guided design of efficient surface modifications to yield battery electrode materials with increased stability against the electrolyte.

Orientation control of thin film nanostructures derived from block copolymers (BCPs) are of great interest for various emerging technologies like separation membranes, nanopatterning, and energy storage. While many BCP compositions have been developed for these applications, perpendicular orientation of these BCP domains is still very challenging to achieve. Herein we report on a new, integration-friendly approach in which small amounts of a phase-preferential, surface active polymer (SAP) was used as an additive to a polycarbonate-containing BCP formulation to obtain perpendicularly oriented domains with 19 nm natural periodicity upon thermal annealing. In this work, the vertically oriented BCP domains were used to demonstrate next generation patterning applications for advanced semiconductor nodes. Furthermore, these domains were used to demonstrate pattern transfer into a hardmask layer via commonly used etch techniques and graphoepitaxy-based directed self-assembly using existing lithographic integration schemes. We believe that this novel formulation-based approach can easily be extended to other applications beyond nanopatterning.

No abstract