Background-The influence of muscle forces and associated physiologic behaviors on dental and skeletal development is well recognized but difficult to quantify because of the limited understanding of the interrelationships between physiologic and other mechanisms during growth.

The recurrence rate after conservative treatment was higher than that after radical treatment. These results are similar to those reported in the literature. The choice of treatment must be adapted to the macroscopic and histological characteristics of each tumour and to the patient.

Reconstructive treatments for jaw defects are complex procedures that can combine multiple techniques including fibula free flap (FFF) grafting. The purpose of this retrospective study was to document and share our experience on mandibular and maxillar reconstruction with FFF followed by secondary dental rehabilitation using implant insertion.We reviewed 198 patients treated by FFF grafting for mandibular and/or maxillary defects in our department during the past 11 years (1996-2007). A selection of 30 patients (18 males and 12 females, mean age of 46 y) with adequate criteria (hygiene, motivation, and prognosis) received secondary placement of osseointegrated implants. The implant success was clinically and radiographically evaluated.A total of 105 osseointegrated implants were placed in the grafted fibulas 5 months to 3 years after the reconstruction surgery. Only 4 implants were lost because of peri-implantitis (3 patients) and fibular fracture (1 patient); this corresponds to a 96.2% implant success rate.During the mean follow-up of 76 months, patient's satisfaction and functional and aesthetic results were evaluated. Radiologic findings indicated a low crest resorption around the implants despite an unfavorable crown-to-root ratio.The main difficulties in the reconstructions were lack of FFF height, absence of a vestibular groove, limitation of mouth opening, skin paddle thickness, and the reconstruction of surrounding tissues including the lip. Our management strategy is discussed.Prosthetic choice is fundamental to achieving patient-specific solutions. The prostheses used included sealed or screwed bridge, resin-bonded bridge, tooled bar, implant-borne denture, or implant-stabilized dentures. Dental implants may be used even in situations involving an unfavorable crown-to-root ratio and implant position by using milled bar and overdenture. The FFF provides a consistent bone graft that allows a reliable and predictable restoration with dental implants, leading to a satisfactory functional and aesthetic restoration.

This homogeneous series is the largest to date and emphasizes the major impact of clear margins and multidisciplinary management. Neoadjuvant chemotherapy improves disease-free survival and should be recommended for both high and intermediate grade MOS.

We study sexual populations structured by a phenotypic trait and a space variable, in a non-homogeneous environment. Departing from a structured population equation we perform a hydrodynamic-type limit to derive a model close to an existing model of theoretical biology. We then perform a further simplification to obtain a model depending on only one parameter that indicates how fast the environment is changing. We show that depending on this parameter, there exist either propagating waves, where the population invades the entire environment, or steady-states where the population survives but remains in a limited range. The corresponding propagating fronts connect an unstable steady point to a singular point. Existence of steady states with limited range distinguishes the dynamics of the sexual populations from asexual populations, where the populations whether gets extinct or propagates to the whole environment. Numerical simulations show that the derived simplified model is a good approximation of the initial structured population model.

Introduction We investigated if ACTN3, ENPP1, ESR1, PITX1 and PITX2 genes which contribute to sagittal and vertical malocclusion also contribute to facial asymmetries and TMD before and after orthodontic and orthognathic surgery treatment. Methods One hundred seventy four dentofacial deformity patients were diagnosed as symmetric or subdivided into four asymmetric groups according to PA cephalometric measurements. TMD exam diagnosis and Jaw Pain and Function-(JPF) questionnaires assessed presence and severity of TMD. Results Fifty two % of patients were symmetric and forty eight % asymmetric. The asymmetry classification demonstrated significant cephalometric differences between symmetric and asymmetric groups, and across the four asymmetric subtypes: Group 1 - mandibular body asymmetry, Group 2 - ramus asymmetry, Group 3 - atypical asymmetry and Group 4 - “C-shaped” asymmetry. ENPP1 SNP-rs6569759 associated with asymmetry Group 1(p=0.004), and rs858339 with asymmetry Group 3 (p=0.002). ESR1 SNP-rs164321 associated with asymmetry Group 4 (p=0.019). These results are confirmed by Principal Component Analysis (PCA) that showed three principal components explaining almost 80% of the variation seen in the studied group. PC1 and PC2 were associated with ESR1 SNP-rs3020318 (p<0.05). Diagnoses of disc displacement with reduction, masticatory muscle myalgia and arthralgia were highly prevalent in the asymmetry groups and all had strong statistical association to ENPP1 rs858339. The average JPF scores for asymmetric subjects before surgery (JPF=7), were significantly higher than symmetric subjects (JPF=2). Patients with asymmetry Group 3 reported the highest preoperative JPF scores and Group 2 and 3 were most likely to be cured of TMD one year after treatment. Conclusions PA cephalometrics can classify asymmetry into distinct groups; identify probability of TMD and genotype associations. Orthodontic and orthognathic treatment of facial asymmetry is very effective at eliminating TMD in most patients.

BackgroundRelations between maxillo-mandibular deformities and TMJ disorders have been the object of different studies in medical literature and there are various opinions concerning the alteration of TMJ dysfunction after orthognathic surgery. The purpose of the present study was to evaluate TMJ disorders changes before and after orthognathic surgery, and to assess the risk of creating new TMJ symptoms on asymptomatic patients.MethodsA questionnaire was sent to 176 patients operated at the Maxillo-Facial Service of the Lille's 2 Universitary Hospital Center (Chairman Pr Joël Ferri) from 01.01.2006 to 01.01.2008. 57 patients (35 females and 22 males), age range from 16 to 65 years old, filled the questionnaire. The prevalence and the results on pain, sounds, clicking, joint locking, limited mouth opening, and tenseness were evaluated comparing different subgroups of patients.ResultsTMJ symptoms were significantly reduced after treatment for patients with pre-operative symptoms. The overall subjective treatment outcome was: improvement for 80.0% of patients, no change for 16.4% of patients, and an increase of symptoms for 3.6% of them. Thus, most patients were very satisfied with the results. However the appearance of new onset of TMJ symptoms is common. There was no statistical difference in the prevalence of preoperative TMJ symptoms and on postoperative results in class II compared to class III patients.ConclusionsThese observations demonstrate that: there is a high prevalence of TMJ disorders in dysgnathic patients; most of patients with preoperative TMJ signs and symptoms can improve TMJ dysfunction and pain levels can be reduced by orthognathic treatment; a percentage of dysgnathic patients who were preoperatively asymptomatic can develop TMJ disorders after surgery but this risk is low.

A low‐cost 3D printed model has been introduced into the oral and maxillofacial surgery teaching program of undergraduate students to improve education and mechanical comprehension of craniofacial trauma. Steps of the 3D printed haptic model building process are listed. 3D printed models of facial fractures were obtained from Data Imaging and Communications in Medicine (DICOM) data. Computed Aided Design and Manufacturing (CAD‐CAM) freeware was used to create new fractures on the standard tessellation language (STL) file. 3D printed haptic model appears to be an efficient low‐cost support for craniofacial trauma education of undergraduate students.