Die korrosionsbestandigen Stlhle gehbren mit zu den wichtigsten Werkstoffen des chemischen Apparatebaus. Um den standig steigenden Anforderungen N entsprechen, wurde in den letzten Jahren eine Reihe von Sonderstahlen entwickelt. Uber zwei derartige Stahle wird berichtet. VEW A %3 ist ein austenitischer CrNiMo-Stahl mit etwa 6,3% Molybdin, der eine hervorragende Bestlndigkeit in hochchloridhaltigen Medien, das heist, cine ausgezeichnete LochfraO-und Spaltkorrosionsbestandigkeit hat. Die Priifung auf SpannungsriBkorrosion in NaCI-Losung unter Krustenbildung zeigt eine starke Uberlegenheit des Stahles VEW A 963 gegeniiber den CrNiMo-Stahlen mit bis zu 4.5% Molybdan. Auch die Bestiindigkeit in Sauren kann als sehr gut bezeichnet werden. Der Stahl ist gut schweiObar, und SchweiBzusatzwerkstoffe stehen in Form von SchutzgasschweiBdrLhten und umhiillten Elektroden zur Verfii-gun&! . Die Erzeugung des Stahles VEW A 963 ist groBtechnisch als Blech, Stabstahl, Schmiedestiick und Nahtlosrohr moglich. VEW A 905 ist ein austenitisch-ferritischer CrNiMo-Stahl mit Mangan-und Stickstoffzusatz. Durch diese Zusatze wird im losungsgegliihten Zustand eine 0,2-%-Dehngrenze von > 590 Nlmm' erreicht. Das Gefiige besteht zu etwa gleichen Teilen aus Austenit und Ferrit, wobei sich die Anteile mit steigender Temperatur kaum andern. Dies ist fiir die gute SchweiBbarkeit des Stahles wesentlich. Es kommt neben dem SchweiSgut weder zu einer Grobkornbildung, noch entsteht ein Ferritsaum. Eine artgleiche Elektrode ist verfiigbar. VEW A 905 hat eine gute LochfraBbestandigkeit und ein gutes Korrosionsverhalten in verschiedenen Sauren. Besonders hervorzuheben ist die gute Bestlndigkeit gegen Chlorid-SpannungsriBkorrosion. Wie VEW A 963 wird auch VEW A 905 groBtechnisch als Blech, Stabstahl, Schmiedestiick und Nahtlosrohr hergestellt.Stainless steels are among the materials most predominantly used in chemical plant engineering. During the past few years, quite a numbei
Investigations carried out by several institutions under Projects RP559, RP2060, RP1403, RP2741 for the Electric Power Research Institute, Palo Alto, CA, resulted in a 3.5% NiCrMoV steel completely free from temper embrittlement as a material for low pressure rotors but also for combination proberty rotors, for example, integral high-pressure low-pressure (HILP) rotors for future steam plants. This steel contains very low percentages of residual elements including sulfur and phosphorus, and its contents of aluminum, silicon, and manganese are also very low.
The main problem in producing such a steel on an industrial scale is gaining a sufficiently low oxygen content as a precondition for successful desulfurization and high cleanliness. This situation is only possible by applying ladle refining techniques. Two model rotors of this “super clean steel” were produced and tested. The tests proved complete resistance to temper embrittlement.
As an approach for further process development and for the economic production of “super clean steels,” the mechanism governing the deoxidation was investigated in detail by means of trial heats. The influences of the composition of process slags and the influence of the ladle linings were examined. The deoxidation was found mainly to be based on steel-slag reactions. The minimum oxygen content achievable in the steel is limited by interactions between ladle linings and melt, which create a dissociation of the linings and an oxygen supply to the liquid steel.
A round robin test for determination of critical pitting temperature (CPT) according to ASTM G48 produced unsatisfactory repeatability and reproducibility of results in agreement with literature. Investigations on experimental procedure, identification of pits and gravimetric evaluation of samples have been performed to identify crucial parameters for improvement of results.
Several recommendations within ASTM G48 practice are proposed such as wet grinding of specimens, cold drying of specimens, additional gravimetric evaluation and optical evaluation only by skilled persons.
A further suggestion is a finer ground surface of samples. In order to confer statistical reference to CPT values an evaluation of medians with 50% probability of pitting is proposed.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.