No abstract

Brick workers and their families in Nepal generally live in poorly ventilated on-site housing at the brick kiln, and may be at higher risk for non-occupational exposure to fine particulate matter air pollution and subsequent respiratory diseases due to indoor and outdoor sources. This study characterized non-occupational exposure to PM2.5 by comparing overall concentrations and specific chemical components of PM2.5 inside and outside of brick workers’ on-site housing. For all samples, the geometric mean PM2.5 concentration was 184.65 μg/m3 (95% confidence interval: 134.70, 253.12 μg/m3). PM2.5 concentrations differed by kiln number (p = 0.009). Kiln number was significantly associated with 16 of 29 (55%) air pollutant, temperature, or relative humidity variables. There was not a significant interaction between kiln number and location of sample for PM2.5 (p = 0.16), but there was for relative humidity (p = 0.02) and temperature (p = 0.01). Results were qualitatively similar when we repeated analyses using indoor samples only. There was no difference in the chemical makeup of indoor and outdoor PM2.5 in this study, suggesting that outdoor PM2.5 air pollution easily infiltrates into on-site brick worker housing. Outdoor and indoor PM2.5 concentrations found in this study far exceed recommended levels. These findings warrant future interventions targeted to this vulnerable population.

The concentrations of mercury in forty, commercially available dietary supplements, were determined using a new, inexpensive analysis technique. The method involves thermal decomposition, amalgamation, and detection of mercury by atomic absorption spectrometry with an analysis time of approximately six minutes per sample. The primary cost savings from this approach is that labor-intensive sample digestion is not required prior to analysis, further automating the analytical procedure. As a result, manufacturers and regulatory agencies concerned with monitoring lot-to-lot product quality may find this approach an attractive alternative to the more classical acid-decomposition, cold vapor atomic absorption methodology. Dietary supplement samples analyzed included astragalus, calcium, chromium picolinate, echinacea, ephedra, fish oil, ginger, ginkgo biloba, ginseng, goldenseal, guggul, senna, St John's wort, and yohimbe products. Quality control samples analyzed with the dietary supplements indicated a high level of method accuracy and precision. Ten replicate preparations of a standard reference material (NIST 1573a, tomato leaves) were analyzed, and the average mercury recovery was 109% (2.0% RSD). The method quantitation limit was 0.3 ng, which corresponded to 1.5 ng/g sample. The highest found mercury concentration (123 ng/g) was measured in a concentrated salmon oil sample. When taken as directed by an adult, this product would result in an approximate mercury ingestion of 7 µg per week.

Plasma damage of low-k dielectrics during photoresist (PR) stripping in a dual-damascene process is a critical issue in the application of copper/low-k technology for ⩽45nm nodes to increase the signal processing speed of integrated circuit devices. In this article, a detailed and systematic work has been conducted to study the low-k damage on porous methyl silsesquioxane ultralow-k films using various PR strip chemistries and process conditions on a high density plasma reactor. The experimental results obtained from different test methodologies show that the low-k damage generated under fixed process conditions increases in the order of NH3<N2<H2∕N2<H2<O2. Among plasma control parameters, bias power has a very pronounced effect on low-k damage for reducing chemistries due to the acceleration of Si–C bond breaking by ion bombardment. Source power also affects the low-k damage significantly as it controls the ion density and flux to the wafer surface. The pressure effect is more complicated and shows different characteristics for oxidizing and reducing chemistries. The extent of low-k damage depends on the orientation of the wafer surface exposed to the plasma, leading to different sensitivity of the damage to the strip chemistry and process condition. Based on this work, an optimized chemistry and process regime are identified to effectively reduce low-k damage and achieve good strip process performance.

Objectives. To evaluate lead levels in tap water at licensed North Carolina child care facilities. Methods. Between July 2020 and October 2021, we enrolled 4005 facilities in a grant-funded, participatory science testing program. We identified risk factors associated with elevated first-draw lead levels using multiple logistic regression analysis. Results. By sample (n = 22 943), 3% of tap water sources exceeded the 10 parts per billion (ppb) North Carolina hazard level, whereas 25% of tap water sources exceeded 1 ppb, the American Academy of Pediatrics’ reference level. By facility, at least 1 tap water source exceeded 1 ppb and 10 ppb at 56% and 12% of facilities, respectively. Well water reliance was the largest risk factor, followed by participation in Head Start programs and building age. We observed large variability between tap water sources within the same facility. Conclusions. Tap water in child care facilities is a potential lead exposure source for children. Given variability among tap water sources, it is imperative to test every source used for drinking and cooking so appropriate action can be taken to protect children’s health. (Am J Public Health. 2022;112(S7):S695–S705. https://doi.org/10.2105/AJPH.2022.307003 )