No abstract

Objective. To investigate the accuracy of dies obtained from single-step and 2-step double-mix impressions. Material and Methods. Impressions (n = 10) of a stainless steel die simulating a complete crown preparation were performed using a polyether (Impregum Soft Heavy and Light body) and a vinyl polysiloxane (Perfectim Blue Velvet and Flexi-Velvet) in two consistencies, in one or two (without relief) steps. Accuracy of the stone dies was accessed at a measuring microscope, using a metallic crown with perfect fit to the reference crown preparation. Data were submitted to 2-way ANOVA and Tukey test (α = 0.05). Results. The single-step technique resulted in slightly larger dies, while the 2-step technique without relief produced significantly smaller dies, when compared to the original stainless steel die. Stone dies obtained from 2-step polyether impressions were significantly smaller when compared to dies obtained from 2-step vinyl polysiloxane impressions (Impregum 2-step: −290.94 ± 71.64 μm; Perfectim 2-step: −201.86 ± 28.58 μm). No significant differences were observed in dies obtained from either polyether or vinyl polysiloxane with the single-step technique (Impregum single-step: 63.52 ± 16.60 μm; Perfectim single-step: 79.40 ± 14.11 μm). Conclusion. Higher discrepancies were detected for the 2-step impression technique without relief for the investigated materials.

No abstract

No abstract

The aim of this study was to investigate the influence of light source, LED unit and halogen lamp (HL), on the effectiveness of Enforce dual-cured cement cured under a ceramic disc. Three exposure times (60, 80 and 120 s) were also evaluated. Two experimental groups, in which the polymerization of the dual-cured cement was performed through a ceramic disc, and two control groups, in which the polymerization of the dual-cured cement was performed directly without presence of ceramic disc were subdivided into three subgroups (three different exposure times), with five specimens each: G1A- HL 60s; G1B- HL 80s; G1C- HL 120s; G2A- LED 60s; G2B- LED 80s; G2C- LED 120s; and control groups: G3A- HL 60s; G3B- HL 80s; G3C- HL 120s; G4A- LED 60s; G4B- LED 80s and G4C- LED 120s. Cement was applied in a steel matrix (4mm diameter, 1.2mm thickness). In the experimental groups, a ceramic disc was placed on top. The cement was light-cured through the ceramic by a HL and LED, however, the control groups were cured without the ceramic disc. The specimens were stored in a light-proof container at 37ºC for 24 hours, then Vickers hardness was determined. A four-way ANOVA and Tukey test (p£ 0.05) were performed. All specimens cured by LED for 60s showed inferior values compared with the halogen groups. In general, light-curing by LED for 80s and 120s was comparable to halogen groups (60s and 80s) and their control groups. LED technology can be viable for light-curing through conventional ceramic indirect restorations, when curing time is increased in relation to HL curing time.

Ainda que eu fale todas as línguas dos homens e dos anjos, se não tiver amor sou como o bronze que soa ou o sino que retine... mesmo que tivesse toda a fé a ponto de, transportar montanhas, se não tiver amor, não serei nada. (São Paulo apóstolo, carta aos Coríntios, Cap. 13)" Dedicatória Dedicatória Dedicatória Dedicatória Dedico este trabalho primeiramente a Deus Deus Deus Deus, por permitir que eu me levantasse todos os dias pensando em ser uma pessoa melhor aos olhos dos que me amam, ou mesmo aos que precisam de mim. À minha querida mãe Rosina Simões Her querida mãe Rosina Simões Her querida mãe Rosina Simões Her querida mãe Rosina Simões Herrera rera rera rera que por meio de sua vida acadêmica brilhante sempre me mostrou a importância da persistência e dedicação, demonstrando que essa formação transcende ao conhecimento e atuando como um elo muito forte de amor em nossa família, ensinando-nos o valor do respeito e união, mesmo nos momentos mais difíceis.