Resumo O uso de vanádio na produção de vergalhões microligados data do início do século XX, sendo amplamente utilizado na construção civil voltada para regiões susceptíveis a abalos sísmicos. Desse modo, este trabalho visa revisar os efeitos promovidos pelo uso do vanádio na fabricação de vergalhões antissísmicos, levando em conta a utilização de dois processos distintos de laminação-Forno de reaquecimento a Gás Natural (FGN) e Laminação Direta (LD)como forma de conferir ganhos em resistência, mantendo-se níveis satisfatórios de tenacidade. Foram realizados ensaios microestruturais e de propriedades mecânicas entre lotes provenientes dos dois processos, avaliando-se propriedades como tamanho de grão médio, limite de escoamento e limite de resistência, correlacionando-as com o efeito provocado pelo uso do vanádio, concluindo-se que seu impacto no refino de grão austenítico/ferrítico e endurecimento via precipitação de carbonitretos de vanádio é de fundamental importância para a obtenção de propriedades mecânicas satisfatórias em vergalhões antissísmicos. Palavras-chave: Aumento de resistência; Aços; Refino de Grão; Precipitação.
ResumoA corrosão é um fenômeno que está intimamente ligado à integridade dos metais e de suas ligas. Esta ocorre de diversas formas, uma das principais é a corrosão localizada na forma de pites, objeto de análise desse estudo, que visa estabelecer um comparativo entre as curvas de polarização cíclica de algumas ligas ferrosas e não ferrosas, ensaiadas em solução de NaCl 0,6 M, mostrando a agressividade que a solução exerce sob cada uma das ligas. Os materiais analisados nesse estudo foram os aços inoxidáveis AISI 304, AISI 444, super duplex ASTM A890/A890 M Grau 6A, o aço carbono AISI 1030, o alumínio comercialmente puro, o cobre eletrolítico e a liga zircaloy-4. Inicialmente foram medidos os potenciais de corrosão (Ec) de cada liga através do monitoramento do potencial de circuito aberto. Foram realizados os ensaios de polarização potenciodinâmica cíclica em cada liga, comparando o aspecto superficial antes e depois do ensaio através de micrografias óticas, possibilitando que fossem observadas as diferenças entre cada material quanto à resistência à corrosão por pites. Observou-se que algumas ligas não apresentam passivação como o caso do alumínio comercialmente puro, e outras apresentaram regiões passivas e histereses bem definidas, ficando evidente que, dentre as ligas analisadas, o aço inoxidável super duplex ASTM A890/A890 M Grau 6A apresentou os melhores resultados frente aos efeitos agressivos dos íons Cl -presentes na solução, sendo o menos suscetível à corrosão por pites. Palavras-chave: Corrosão por pites; Polarização cíclica; NaCl 0,6M; Ligas não ferrosas. COMPARATIVE STUDY OF CORROSION RESISTANCE BETWEEN FERROUS AND NONFERROUS METALLIC ALLOYS AbstractCorrosion is a phenomenon that is closely linked to the integrity of the metal and its alloys. This occurs in many ways, one of the main is localized corrosion in the form of pits, object of analysis in this study, that aims to establish a comparison between the cyclic polarization curves of some ferrous and non-ferrous alloys, tested in 0,6M NaCl solution, showing aggressivity the solution exerts on each of the alloys. The materials analyzed in this study were the stainless steel AISI 304, AISI 444, super duplex ASTM A890 / A890 M Grade 6A, carbon steel AISI 1030, commercially pure aluminum, electrolytic copper and zircaloy-4 alloy. Initially the corrosion potentials were measured (Ec) from each alloy through the open circuit potential monitoring. The cyclic potentiodynamic polarization tests on each alloy were conducted, comparing the surface appearance before and after the test by optical micrographs, enabling that differences were observed between each material for resistance to pitting corrosion. It was observed that some alloys do not exhibit passivation such as the case of commercially pure aluminum, and others showed passive regions and well defined hysteresis, being evident that, among the examined alloys, super duplex stainless steel ASTM A890 / A890 M Grade 6A presented best results against the harsh effects of Cl -ions present in the solution...
Resumo No processo de laminação a quente ocorre ocasionalmente a perda de ductilidade a quente que pode causar o fenômeno denominado como "abertura de cabeça" da barra durante a sequência de passes. Essa perda de ductilidade a quente pode ser severa e causar interrupções no processo produtivo. Esse fenômeno pode estar associado a diversos fatores entre eles: composição química do aço; defeitos presentes no tarugo; condições do processo de laminação; e temperatura do aço durante o processo, principalmente nos passes de desbaste e intermediários de laminação. No processo em estudo, a perda de ductilidade a quente ocorre associada à laminação de vergalhões a partir de tarugos oriundos diretamente do lingotamento contínuo. O presente trabalho tem como objetivo avaliar a influência da temperatura e da microestrutura formada ao longo do processo na perda de ductilidade a quente das barras através de um exame comparativo entre os vergalhões laminados com e sem o uso da etapa de reaquecimento. Palavras-chave: Laminação a quente; Perda de ductilidade a quente; Temperatura; Caracterização Microestrutural.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.