The present work analyzes the influence of an orthogonal machining process on the generation of nanocrystalline surface layers. Thereby, AISI 4140 is used as work piece material. Metallic parts with a severe nanocrystalline grain refinement in the near-surface area show many beneficial properties. Such surface layers considerably influence the friction and wear characteristics of the work piece in a subsequent usage as design elements working under tribological loads. The focus of this paper is an experimental analysis of a finishing orthogonal cutting operation, carried out with a broaching machine, to generate nanocrystalline surface layers. The influence of process and geometry parameters on the generation of nanocrystalline surfaces is investigated with the aim to massively decrease the grain size in the work piece surface layer. Parameters that are studied and taken into account in the manufacturing process are cutting edge radius rβ, depth of cut h and cutting velocity vc. The cutting edge radius rβ is modified by a drag finishing process. The generation of nanocrystalline surface layers is especially influenced by the design of the uncoated carbide cutting tools. Additionally, cutting force Fc and passive force Fp are determined by a 3-component dynamometer to calculate the relationship between specific cutting force kc and specific passive force kp. The temperature beneath the clearance face is detected by a fiber optic pyrometer. These measurement methods and devices are applied to detect the impact of the most relevant measurement values occurring during machining and causing a drastic reduction of grain size in the surface layer. The evaluation of the manufacturing process is carried out by detailed analyses of the microstructural conditions in the surface layer after processing using a Focused Ion Beam (FIB) system. These material characterizations provide information about the surface engineering concerning the microstructural changes in the surface layer of the work piece due to finishing orthogonal cutting processes.
Present work analyzes the influence of process and modified geometry parameters of an orthogonal final machining process (finishing) on the nanocrystalline surface layers generation by quantitative microstructural analysis. Thereby, AISI 4140 (German Steel 42CrMo4) in a state quenched and tempered at 450°C is used as workpiece material. Metallic materials used in technical applications are polycrystalline in nature and are composed of a large number of grains which are separated by grain boundaries. The grain size has a strong influence on the mechanical material properties. Metallic parts with a severe nanocrystalline grain refinement in the near-surface area show many beneficial properties. Such surface layers considerably influence the friction and wear characteristics of the workpiece in a subsequent usage as design elements working under tribological loads due to their extreme superplastic properties. The tribologically induced surface layers formation already starts during the manufacturing of the components, by leading to a change of workpiece material near the surface. Particularly when the depth of cut h becomes of the same order as the cutting edge radius rß, the ploughing process becomes increasingly important and strongly influences the chip formation process. The plastic zone depth within the surface layer is especially influenced by the design of the microgeometry of the cutting tools and increases almost linearly with the ratio of cutting edge radius rß to depth of cut h. The plastic zone is hereby approximately of the same order of magnitude as the cutting edge radius rß. Parameters that are studied and taken into account in the manufacturing process are cutting edge radius rß, depth of cut h and cutting velocity vc. Variations of cutting depth h are performed in a range of 30 to 100 µm and variations of cutting edge radius rß are executed in a range of 30 to 150 µm. The microgeometries of the tools are preconditioned by abrasive grinding with a drag finishing machine and observed by a confocal light microscope. A cutting velocity vc of 25 and 150 m/min is applied. The evaluation of the manufacturing process is carried out by detailed analyses of the microstructural conditions in the surface layer after processing using a Focused Ion Beam system. These material characterizations provide information about the surface engineering concerning the microstructural changes in the workpiece surface layer due to machining. Hereby, the grain size analysis is investigated by a line method based on the characterization of portions of several test-lines positioned across the two dimensional Focused Ion Beam images.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.