In the last decade, environmental risks associated with wastewater treatment plants (WWTPs) have become a concern in the scientific community due to the absence of specific legislation governing the occupational exposure limits (OEL) for microorganisms present in indoor air. Thus, it is necessary to develop techniques to effectively inactivate microorganisms present in the air of WWTPs facilities. In the present work, ultraviolet light A radiation was used as inactivation tool. The microbial population was not visibly reduced in the bioaerosol by ultraviolet light A (UVA) photolysis. The UVA photocatalytic process for the inactivation of microorganisms (bacteria and fungi, ATCC strains and isolates from indoor air samples of a WWTP) using titanium dioxide (TiO P25) and zinc oxide (ZnO) was tested in both liquid-phase and airborne conditions. In the slurry conditions at liquid phase, P25 showed a better performance in inactivation. For this reason, gas-phase assays were performed in a tubular photoreactor packed with cellulose acetate monolithic structures coated with P25. The survival rate of microorganisms under study decreased with the catalyst load and the UVA exposure time. Inactivation of fungi was slower than resistant bacteria, followed by Gram-positive bacteria and Gram-negative bacteria. Graphical abstract Inactivation of fungi and bacteria in gas phase by photocatalitic process performed in a tubular photoreactor packed with cellulose acetate monolith structures coated with TiO.

No abstract

URB is a research project designed to collect and store raw data from soundscapes analysis. This paper presents a survey about using URB based on the analysis of work developed by several artists, focusing on the description of their creative process and outcome. By comparing the processes and statements of each artists, the authors identified diverse systematic approaches to reinterpreting raw data provided by urban soundscapes, raising questions about the artistic outcomes vs original sound sources. Furthermore, some considerations are inferred about the artistic relevance of using this process in the creation process.

Cellulose acetate monoliths (CAM) were used as the substrate for the deposition of TiO2 films to produce honeycombed photoactive structures to fill a tubular photoreactor equipped with a compound parabolic collector. By using such a setup, an efficient single-pass gas-phase conversion was achieved in the degradation of n-decane, a model volatile organic compound. The CAM three-dimensional, gas-permeable transparent structure with a rugged surface enables a good adhesion of the catalytic coating. It also provides a rigid structure for packing the tubular photoreactor, and maximizing the illuminated catalyst surface. The efficiency of the photocatalytic oxidation (PCO) process on n-decane degradation was evaluated under different operating conditions, such as feeding concentration (73 and 146 ppm), gas stream flow rate (73, 150, and 300 mL min(-1)), relative humidity (3 and 25 %), and UV irradiance (18.9, 29.1, and 38.4 WUV m(-2)). The results show that n-decane degradation by neat photolysis is negligible, but mineralization efficiencies of 86 and 82 % were achieved with P25-CAM and SG-CAM, respectively, for parent pollutant conversions above 95 %, under steady-state conditions. A mass transfer model, considering the mass balance to the plug-flow packed photoreactor, and PCO reaction given by a Langmuir-Hinshelwood bimolecular non-competitive two types of sites equation, was able to predict well the PCO kinetics under steady-state conditions, considering all the operational parameters tested. Overall, the performance of P25-CAM was superior taking into account mineralization efficiency, cost of preparation, surface roughness, and robustness of the deposited film.

The modification of titanate nanotubes (TiNT) with nitrogen (NTiNT) was accomplished through impregnation method. TiNT were synthesized via hydrothermal treatment of titania powders in NaOH solution at 130 °C for 48 h. The obtained samples were characterized by UV-Vis absorption spectroscopy, Brunauer-Emmett-Teller (BET) surface area, XRD, TEM, XPS, and TG analysis. Structure, morphology, composition, and visible light absorption property of nitrogen-modified TiO2 nanotubes are found to depend on the nitrogen content and not on the calcination temperature for the range used in this work. The photocatalytic activity of these nanotubes was investigated for the degradation of methylethylketone (MEK) and hydrogen sulfide (H2S) under ultraviolet and solar light radiation. MEK is very resistant to photocatalytic degradation with the prepared materials;, however, the results show that modification of the TiNT with nitrogen in a proportion of 1 to 1 (TiNT to urea weight ratio) and calcination at 400 °C lead to materials with high photocatalytic activity under ultraviolet radiation and moderate photocatalytic activity under solar radiation for degradation of H2S.