Immiscibility between dimethyl sulfoxide (DMSO) and polar solvents used for poly(N-vinylcarbazole) (PVK) solutions, leads to failed light-emitting diodes when colloidal cadmium sulfide (CdS) nanoparticles capped with thiophenol are incorporated to their active layer. To prevent this, a heat treatment is applied to the CdS nanoparticles in order to evaporate DMSO solvent. After evaporation most of the nanoparticles increased their size, and some of them show hexagonal crystalline structure instead of the original cubic zinc-blende observed in colloidal pre-treated nanoparticles. Nevertheless, enhanced electronic properties are measured in light-emitting devices when DMSO-free nanoparticles are embedded in the poly(N-vinylcarbazole) active layer. Light emission from these hybrid devices comprises the whole visible range of wavelengths as searched for white LEDs. Moreover, electroluminescence from both types of CdS nanoparticles (smaller cubic and bigger hexagonal) has been discriminated and interpreted through Gaussian deconvolution.
In this article, we compare two different kinds of commercial light-emitting diodes (LEDs) in transmission and organic photodetectors based on poly(3-hexylthiophene) (P3HT) and a phenyl-C61-butyric acid methyl ester (PCBM) blend used as active layer in reception. Photovoltaic cells based on massive heterojunctions of semiconductor polymers have focused the attention of researchers due to their several potential advantages over their inorganic counterparts, such as their simplicity, low cost, and ability to process large area devices, even on flexible substrates. Furthermore, in logistics, storage management systems require the implementation of technological solutions that allow the control of merchandise in real time by means of light-emitting diode signals that send information about the product. However, the slow response time of these organic photodetectors should not be critical for this application, where the light intensity changes are very slow, which limits the speed of data transmission compared to inorganic based systems that use wireless optical communications. Finally, we show a low-cost visible light communication system based on organic photodetectors with a frame based on on-off keying with Manchester encoding to support device-to-device connections.
In this paper, we compare four different methods to estimate nanoparticle diameters from optical absorption measurements, using transmission electron microscopy (TEM) images as a reference for the nanoparticle size. Three solutions of colloidal nanoparticles coated with thiophenol with different diameters were synthesized by thiolate decomposition. The nanoparticle sizes were controlled by the addition of a certain volume of a 1% sulphur solution in toluene. TEM measurements showed that the average diameter for each type of these nanoparticles was 2.8 nm, 3.2 nm, and 4.0 nm. The methods studied for the calculation of the nanoparticles diameter were: The Brus model, the hyperbolic band model (HBM), the Henglein model, and the Yu equation. We evaluated the importance of a good knowledge of the nanoparticle bandgap energy, and the nature of electronic transitions in the semiconductor. We studied the effects that small variations in the electron and hole effective mass values produced in the Brus equation and in the HBM model for CdS, PbS, and ZnS nanoparticles. Finally, a comparison was performed between the data provided by these models and the experimental results obtained with TEM images. In conclusion, we observed that the best approximation to the experimental results with TEM images was the Brus equation. However, when the bandgap energy was close to the bulk bandgap energy, the theoretical models did not adjust correctly to the size measured from the TEM images.
In this study, poly(9-vinylcarbazole) (PVK)-based LEDs doped with reduced graphene oxide (rGO) and cadmium sulphide (CdS) nanocrystals were fabricated by spin-coating. The hybrid LED structure was a layer sequence of glass/indium tin oxide (ITO)/PEDOT:PSS|rGO/PVK/Al. rGO was included in the poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) layer due to its energy bands being close to PEDOT:PSS bands, and the possibility of using water for dispersing both polymer and flakes. Optical properties such as photoluminescence and UV-Vis absorption were not affected by the addition of rGO to the PEDOT:PSS solution. However, PVK-based LEDs with rGO showed increased current density compared to those without rGO in the hole transporting layer. Higher electroluminescence intensities were observed for rGO-enriched LEDs, although the shape of the spectrum was not modified. LEDs including CdS nanocrystals in the poly(9-vinylcarbazole) emissive layer did not show such dependence on the rGO presence. Though the addition of rGO to PEDOT:PSS still produces a slightly higher current density in CdS doped LEDs, this growth is no longer proportional to the rGO load.
In Visible Light Communication (VLC) Systems, data are transmitted by modulating light from an illumination source, that could be an ordinary lamp or light-emitting diodes (LEDs). Photovoltaic cells based on massive heterojunctions of semiconductor polymers have focused the attention of researchers due to several potential advantages over their inorganic counterparts, such as simplicity, low cost and the ability to process large area devices even on flexible substrates. In this paper, we use commercial LEDs in transmission and organic photodetectors (OPD) based on poly(3-hexylthiophene) (P3HT) and a phenyl-C61-butyric acid methyl ester (PCBM) blend used as active layer in reception. We have fabricated and characterized the I-V curve and the Bit Error Rate (BER) response of the OPD using low cost processing techniques and we have used an Atmel 8-bit microcontroller in order to control the electronics to transmit and modulate the signal. Finally, in this work, we have developed and characterized organic photodetectors in a low cost visible light communications system capable of transmitting an image file in real-time, as a proof of concept that is cost effective, since the whole system was implemented using low cost components. You can find more information in the supplementary materials.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.