Objective:The aim of the study was to evaluate the microtensile bond strength (µTBS) of Scotchbond Universal to dentin using the etch-and-rinse or the self-etch technique after 24 h and 6 months of storage.Materials and Methods:Flat dentin surfaces were obtained in 24 third molars. The teeth were divided into four groups: G1 – Scotchbond Universal applied in the etch-and-rinse mode; G2 – Scotchbond Universal applied in the self-etch mode; G3 – Scotchbond Multi-Purpose; G4 – Clearfil SE Bond. A block of composite was built on the adhesive area. The tooth/resin sets were cut parallel to the long axis to obtain 40 beams (~0.8 mm2) for each group. Twenty specimens were immediately submitted to the µTBS test, and the remaining 20 were stored in water for 6 months. Failures and the adhesive interface were analyzed by SEM.Results:According to two-way ANOVA, the interaction between adhesive and storage time was significant (p=0.015).The µTBS (MPa) means were the following: 24 h – G1 (39.37±10.82), G2 (31.02±13.76), G3 (35.09±14.03) and G4 (35.84±11.06); 6 months – G1 (36.99±8.78), G2 (40.58±8.07), G3 (32.44±6.07) and G4 (41.75±8.25). Most failures were mixed. Evidence of hybrid layer and numerous resin tags were noted for Scotchbond Universal applied with the etch-and-rinse mode and Scotchbond Multi-Purpose. A thinner hybrid layer and fewer resin tags were noted for Scotchbond Universal applied in the self-etch mode and Clearfil SE Bond.Conclusion:The results indicate that the µTBS for Scotchbond Universal is comparable to the gold-standard adhesives. Scotchbond Universal applied in the self-etch mode and Clearfil SE Bond revealed higher bond stability compared to the etch-and-rinse mode.

SUMMARY The aim was to evaluate, in vitro, quantitatively and qualitatively, the effect of pH cycling and simulated toothbrushing on surface roughness (Ra) and bacterial adhesion (Cn) of bulk-fill composite resins. Thirty specimens of each composite resin, 5 mm wide and 4 mm high, were obtained: group 1 (control): Filtek Z250 (Z250); group 2: Filtek Bulk-Fill (FTK); group 3: Tetric N-Ceram Bulk-Fill (TTC); and group 4: Aura Bulk-Fill (AUR). After 24 hours, the specimens were polished and then alternated with demineralization/remineralization solutions for 15 cycles of 24 hours each at 37°C. Then the specimens were submitted to simulated toothbrushing. The Ra and Cn measurements were quantitatively analyzed in three stages: after polishing (Ra0 and Cn0), after pH cycling (Ra1 and Cn1), and after simulated toothbrushing (Ra2 and Cn2). The Ra values were submitted to two-way analysis of variance, followed by the Tukey test (α=0.05). The Kruskal-Wallis test, followed by multiple comparisons, was applied for Cn analysis. Surface topography and bacterial adhesion were observed by scanning electron microscopy (SEM). Z250, FTK, and TTC showed no significant change in Ra regardless of the treatment performed; AUR obtained increased Ra at Ra2 (p<0.05). FTK differed from the others at Cn0 and Cn1 (p<0.05). At Cn2, there was no difference among the composite resins. SEM images showed the exposure of fillers and microcavities at Ra1 and Ra2. There was greater bacterial adhesion at Cn1 for Z250 and FTK. It was concluded that the pH cycling caused surface degradation of all composite resins, which was potentiated by simulated toothbrushing. However, only AUR presented an increased Ra. Bacterial adhesion occurred on all composite resins after pH cycling; however, after simulated toothbrushing, adhesion of dispersed bacteria was similar for all the composite resin groups.

Introduction: Material biodegradation that occurs in the mouth may interfere in the bonding strength between the bracket and the enamel, causing lower bond strength values in vivo, in comparison with in vitro studies. Objective: To develop a prototype to measure bracket debonding force in vivo and to evaluate, in vitro, the bond strength obtained with the prototype.Methods: A original plier (3M Unitek) was modified by adding one strain gauge directly connected to its claw. An electronic circuit performed the reading of the strain gauge, and the software installed in a computer recorded the values of the bracket debonding force, in kgf. Orthodontic brackets were bonded to the facial surface of 30 bovine incisors with adhesive materials. In Group 1 (n = 15), debonding was carried out with the prototype, while tensile bond strength testing was performed in Group 2 (n = 15). A universal testing machine was used for the second group. The adhesive remnant index (ARI) was recorded.Results: According to Student’s t test (α = 0.05), Group 1 (2.96 MPa) and Group 2 (3.08 MPa) were not significantly different. ARI score of 3 was predominant in the two groups.Conclusion: The prototype proved to be reliable for obtaining in vivo bond strength values for orthodontic brackets.

Abstract The aim was to evaluate, in vitro, the influence of pH cycling on microtensile bond strength (µTBS) and percentage of nanoleakage (%NL) in the dentin-adhesive interface. Flat dentin surfaces were obtained in 56 extracted third molars. The teeth were randomly divided into four groups (n=14): G1- Single Bond Universal (etch-and-rinse mode); G2- Single Bond Universal (self-etch mode); G3- Scotchbond Multi-Purpose; G4- Clearfil SE Bond. A block of composite was built on the adhesive area. Eight tooth/resin sets were cut parallel to the tooth’s long axis to obtain 48 beams (0.8 mm2) for each group. Half of the beams were submitted to four cycles of pH cycling (demineralizing solution for 6 h and remineralizing solution for 18 h). The samples were submitted to µTBS test in a universal testing machine. Six tooth/resin sets were cut parallel to the tooth’s long axis to obtain three slices of the central region (1.0 mm thickness). Half of the slices were submitted to pH cycling. The nanoleakage methodology was applied to obtain the %NL at the adhesive interfaces. According to two-way ANOVA, the interaction between factors (adhesive system x storage) was significant (p=0.0001) for µTBS and %NL. After pH cycling, there was a significant decrease in µTBS and a significant increase in %NL for all adhesives. The adhesives applied in the self-etch mode obtained lower %NL, differing significantly from the etch-and-rinse adhesives. It was concluded that the pH cycling negatively influenced the µTBS and %NL for all adhesives evaluated. However, self-etch adhesives allowed less %NL.