ABSTRACT:The shape memory behavior of a series of polycaprolactone/methane diisocyanate/ butanediol ( PCL /MDI /BDO) segmented polyurethanes of different composition was studied. The molecular weight of PCL diols was in the range of 1600 -7000, and the hard segment content varied from 7.8 to 27% by weight. Film specimens for shape memory measurements were prepared by drawing at temperatures above the melting temperature of the soft segment crystals and subsequent quick cooling to room temperature under constrained conditions. The shape memory process was observed and recorded in a heating process. Parameters describing the recovery temperature, ability, and speed were used to study the influence of structure and processing conditions on the shape memory behavior of the sample. It was found that the high crystallinity of the soft segment regions at room temperature and the formation of stable hard segment domains acting as physical crosslinks in the temperature range above the melting temperature of the soft segment crystals are the two necessary conditions for a segmented copolymer with shape memory behavior. The response temperature of shape memory is dependent on the melting temperature of the soft segment crystals. The final recovery rate and the recovery speed are mainly related to the stability of the hard segment domains under stretching and are dependent on the hard segment content of the copolymers.
The cationic copolymerization of regular soybean oil, low-saturation soybean oil (LoSatSoy oil), or conjugated LoSatSoy oil with styrene and divinylbenzene initiated by boron trifluoride diethyl etherate (BF 3 ⅐OEt 2 ) or related modified initiators provides viable polymers ranging from soft rubbers to hard, tough, or brittle plastics. The gelation time of the reaction varies from 1 ϫ 10 2 to 2 ϫ 10 5 s at room temperature. The yields of bulk polymers are essentially quantitative. The amount of crosslinked polymer remaining after Soxhlet extraction ranges from 80 to 92%, depending on the stoichiometry and the type of oil used. Proton nuclear magnetic resonance spectroscopy and Soxhlet extraction data indicate that the structure of the resulting bulk polymer is a crosslinked polymer network interpenetrated with some linear or less-crosslinked triglyceride oil-styrene-divinylbenzene copolymers, a small amount of low molecular weight free oil, and minor amounts of initiator fragments. The bulk polymers possess glass-transition temperatures ranging from approximately 0 to 105°C, which are comparable to those of commercially available rubbery materials and conventional plastics. Thermogravimetric analysis (TGA) indicates that these copolymers are thermally stable under 200°C, with temperatures at 10% weight loss in air (T 10 ) ranging from 312 to 434°C, and temperatures at 50% weight loss in air (T 50 ) ranging from 445 to 480°C. Of the various polymeric materials, the conjugated LoSatSoy oil polymers have the highest glass-transition temperatures (T g ) and thermal stabilities (T 10 ). The preceding properties that suggest that these soybean oil polymers may prove useful where petroleumbased polymeric materials have found widespread utility.
A variety of new polymers ranging from rubbery materials to tough and rigid plastics have been prepared by the thermal copolymerization of tung oil, styrene, and divinylbenzene. The thermal copolymerization is performed in the temperature range of 85-160 degrees C with variations in the stoichiometry, oxygen uptake, peroxides, and metallic catalysts used. Gelation of the reactants typically occurs at temperatures higher than 140 degrees C, and fully cured thermosets are obtained after post-curing at 160 degrees C. The fully cured thermosets are determined by Soxhlet extraction to contain approximately 90-100% cross-linked materials, and (1)H NMR and FTIR spectroscopy indicates that the cross-linked materials are random copolymers. The new bulk polymeric materials obtained are light yellow and transparent with glossy surfaces, and possess glass transition temperatures of -2 to +116 degrees C, cross-link densities of 1.0 x 10(3)-2.5 x 10(4) mol/m(3), coefficients of linear thermal expansion of 2.3 x 10(-4)-4.4 x 10(-4) per degrees C, compressive moduli of 0.02-1.12 GPa, and compressive strengths of 8-144 MPa. These materials are thermally stable below 300 degrees C and exhibit a major thermal degradation with a maximum degradation rate at 493-506 degrees C.
SYNOPSISA series of polycaprolactone/4,4'-diphenylmethane diisocyanate/l,4-butanediol (PCL/MDI/ BDO) segmented polyurethanes of different compositions was synthesized by solution polymerization. The molecular weight of PCL diols used was in the range of 1600-7000. The crystallinity and morphology of these polymers were studied by using DSC, dynamic mechanical analysis, WAXD, and polarizing microscopy methods. It was found that the crystallinity of PCL prepolymers was depressed in segmented polyurethanes. A lower limit of PCL molecular weight was found, below which the PCL segments were not able to crystallize a t the usual processing conditions. This limit of molecular weight is in the range of 2000-3000 and exhibits a slight increase with increasing hard-segment content of polyurethanes.The glass transition temperature related to the PCL segment regions in polyurethane specimens deviated from that of pure amorphous PCL prepolymer to a higher temperature. The deviation resulted from the crystallization of PCL segments and also the influence of hard segments. The formation of hard-segment domains becomes very difficult for polyurethanes having low hard-segment content and short hard-segment length. There is a lower limit of hard-segment content and segment length. Only above that limit do the polyurethanes have enough hard-segment domains acting as physical crosslinks at temperatures above the melting point of the PCL crystals. The structural characteristics of segmented polyurethanes which may exhibit a shape memory effect are also discussed.
The cationic copolymerization of tung oil with the divinylbenzene comonomer initiated by boron trifluoride diethyl etherate produces promising plastics. The gel times are largely dependent on the relative composition and the reaction conditions and vary from a few seconds to 1 h. Controlled reactions producing homogeneous materials can be obtained by (1) lowering the reaction temperature or (2) decreasing the initiator concentration to less than 1 wt % or (3) adding a certain amount of a less reactive oil, such as soybean oil, low saturation soybean oil (LoSatSoy), or conjugated LoSatSoy to the reaction. The resulting polymers are rigid and dark brown in color. The weight % of the starting materials converted to the crosslinked polymer is ∼85–98% as determined by Soxhlet extraction with methylene chloride. The structure of the bulk product is that of a crosslinked polymer network plasticized by a small amount of low molecular weight oil. The chemical composition of the bulk polymers varies with the original composition of the tung oil system. Dynamic mechanical analysis shows that the resulting products are typical thermosetting polymers with densely crosslinked structures. The modulus of the plastics is approximately 2.0 × 109 Pa at room temperature. One broad glass transition is observed at approximately 100°C. Thermogravimetric analysis shows that the tung oil polymers are thermally stable below 200°C with a 10% weight loss in air around 430°C. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1044–1056, 2000
ABSTRACT:The polyurethane composites with conducting carbon black (CB) were prepared by a solution-precipitation process, which was followed by melt compression molding. The polyurethane used has good shape memory effect. The morphology of CB fillers in polyurethane matrix and the resulting conductivity of the composites were investigated. It has been found that CB fillers exist in the forms of aggregates. The percolation threshold is achieved at the CB concentration of 20 wt %. The presence of CB fillers decreases the degree of crystallinity of polycaprolactone (PCL) soft segments of the polyurethane. However, the composites still have enough soft-segment crystals of polyurethane to fulfil the necessary condition for the shape memory properties. Dynamic mechanical data show that CB is an effective filler for the reinforcement of the polyurethane matrix, but does not deteriorate the stable physical cross-link structure of the polyurethane, which is necessary to store the elastic energy in the service process of the shape memory materials. Addition of CB reinforcement in the polyurethane has influenced the strain recovery properties, especially for those samples with CB concentrations above the percolation threshold. The response temperature of the shape memory effect T r has not been affected too much. Strain fixation S f , which expresses the ability of the specimens to fix their strain, has been improved in the presence of the CB fillers. The final recovery rates R f and strain recovery speeds V r of the shape memory measurements, however, have decreased evidently. It is expectedly ascribed to the increased bulk viscosity as well as the impeding effect of the inter-connective structure of CB fillers in the polymer matrix.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.