Peningkatan konsumsi pengunaan masker di tingkat rumah tangga sebagai salah satu alat pelindung diri (APD) berdampak pada limbah yang dihasilkan. Bahan masker sekali pakai adalah polipropilena yang merupakan plastik dengan sifat yang sulit terurai dan membutuhkan waktu lama untuk terurai di lingkungan. Sehingga proses daur ulang menjadi salah satu cara yang dapat dilakukan untuk mengurangi dampak lingkungan yang ditimbulkan. Pada daur ulang masker mengunakan metode hot press dengan suhu 200°C, tekanan 100 bar, dan lama waktu pengepresan 5 menit telah berhasil dilakukan. Hal ini membuktikan bahwa limbah masker dengan berat 20 dan 30 g dari tiga lapisan yaitu Luar (L), Tengah (T), Dalam (D) dan campurannya berpotensi untuk diolah menjadi lembaran plastik. Gugus fungsi masker lapisan Luar (L), Tengah (T), Dalam (D), dan lembaran plastik L/T/D dicirikan oleh penyerapan khas polipropilena (PP). Pada lapisan Luar (L) dan lembaran plastik L/T/D terdapat bilangan gelombang pada 2323 cm-1 yang merupakan gugus fungsi CH. Ketebalan lembaran plastik tiga lapisan dan campurannya dengan berat limbah masker 20 dan 30 g adalah antara 0.13 ± 0.01 mm sampai 0.37 ± 0.06 mm dan 0.29 ± 0.02 mm sampai 0.45 ± 0.04 mm, berturut-turut. Morfologi permukaan pada masker lapisan Luar (L), Dalam (D), dan campuran Luar/Tengah/Dalam (L/T/D) memperlihatkan karakteristik yang hampir sama yaitu sedikit beralur. Sedangkan masker lapisan Tengah (T) terlihat seperti terdapat goresan-goresan kecil. Kekuatan tarik dan elongation lembaran plastik dengan berat 20 gram sebagai berikut: lapisan Luar (1.3 MPa dan 0.92%), Tengah (0 MPa dan 0%), Dalam (1.14 MPa dan 2.04%), Luar/Tengah (0.14 MPa dan 0.33%), Luar/Dalam (1.23 MPa dan 1.27%), dan Luar/Tengah/Dalam (0.64 MPa dan 0.64%). Kenaikan berat sampel dari 20 menjadi 30 g secara umum berpengaruh pada ketebalan lembaran plastik, kenaikan kekuatan tarik, dan nilai kemuluran lembaran plastik.Kata Kunci: Limbah masker, lapisan masker, daur ulang, lembaran plastik, karakteristik
Penggunaan masker sekali pakai terkait pandemi Covid-19 di satu sisi melindungi pemakainya dari virus, namun di lain sisi menimbulkan permasalahan terhadap lingkungan. Oleh karena itu, dilakukan sejumlah upaya daur ulang limbah masker, salah satunya dengan mengolahnya menjadi material baru, seperti produk interior, bijih plastik, dan adsorben pada limbah cair industri laundry. Penelitian ini bertujuan untuk menganalisis sifat mekanik lembaran plastik hasil pengolahan limbah masker sekali pakai jenis masker medis tiga lapis (3 ply) dengan variasi berat. Metode yang digunakan adalah tekan panas (hot press) dengan variasi berat 10 gr, 20 gr, 30 gr, 40 gr, 50 gr, dan 60 gr. Pengujian yang dilakukan adalah uji tarik, mulur, dan ketebalan sampel. Hasil dari penelitian menunjukkan bahwa pertambahan berat meningkatkan kekuatan tarik, mulur, dan ketebalan. Sampel dengan berat 10 gr memiliki kekuatan tarik, mulur, dan ketebalan terendah, yaitu masing-masing 0,001 MPa, 0,311%, dan 0,143 mm. Sedangkan sampel dengan berat 60 gr memiliki kekuatan tarik, mulur, dan ketebalan tertinggi, yaitu masing-masing 0,023 MPa, 1,155%, dan 0,837 mm.Kata kunci: mulur, ketebalan, kekuatan tarik, limbah masker, tekan panas
The use of steel in aerospace manufacture continues to decrease, owing in part to the sustainability and mechanical properties of fibers which have higher strength in minimum weight than steel. This study was defined to evaluate the mechanical properties of high-performance fibers, especially aramid, in terms of composite to be part of aircraft' wings called CN-235. The reinforcements were pre-impregnated by the materials manufacturers, under heat and pressure, with a pre-catalysed resin. Then the layering of aramid prepregs was carried with a dry lay-up process and cured in the autoclave at a temperature of 125°C and pressure of 3 bar for 90 minutes. The aramid composite was cured in various grain directions and examined in mechanical tests such as tensile, compression, and interlaminar shear strength tests. The result showed an insignificant difference between 0 and 90 degrees of grain direction in aramid composite in any properties. The strength of aramid composite with 90 degrees of grain direction has a higher value in the compression test (less than 5%) while having lower value in tensile and interlaminar shear tests.
Penyebaran virus corona (COVID-19) telah begitu pesat hingga pemerintah Indonesia mewajibkan penggunaan alat pelindung diri (APD) berupa masker kain bagi masyarakat umum supaya persediaan masker bedah yang stoknya terbatas hanya diperuntukkan bagi tenaga medis. Adaptasi kebiasaan baru, tidak dipungkiri akan tetap menerapkan protokol kesehatan ini tanpa batas waktu yang diketahui. Hal ini dijadikan peluang bisnis bagi UMKM di daerah untuk membuat masker kain dan menjualnya dengan harga terjangkau. Tujuan dari penelitian ini adalah menguji keefektifan dari masker kain dari kenyamanan dengan 2 aspek: objektif dan subjektif. Sampel yang digunakan adalah masker kain hasil UMKM daerah Ngemplak, Sleman Yogyakarta dengan tiga jenis struktur yang berbeda, yaitu masker satu lapis kain rajut dari polikloroprena (PCP) atau dikenal dengan masker scuba, dua lapis masker kain tenun dengan bagian dalam menggunakan poliester dan bagian luar menggunakan kapas (PES/Co), serta tiga lapis masker kain tenun dengan bagian dalam poliester dan bagian tengah-luar adalah kapas (PES/Co2). Untuk pengujian kenyamanan pengguna secara kuantitatif dan objektif dilakukan dengan menggunakan Fabric Touch Tester (FTT) dengan menilai beberapa parameter yaitu kelembutan, kehalusan, dan kehangatan. Kuisioner sebagai data kualitatif mengenai ergonomi, juga dibagikan kepada responden yang menggunakan masker kain produksi UMKM Kecamatan Ngemplak dengan penilaian AATCC parameter 5 yang menilai kehalusan, kehangatan, dan ketebalan dengan skala 1-4. Hasil yang didapatkan adalah masker dua lapis (PES/Co) memiliki keunggulan rata-rata nilai indeks sensorik primer yang tertinggi pada uji kenyamanan menggunakan FTT, sedangkan masker scuba (PCP) memiliki kenyamanan terbaik dinilai oleh pengguna. Masker tiga lapis (PES/Co2) baik secara objektif dan subjektif memiliki nilai terendah karena faktor kehangatan yang tinggi sehingga pengguna merasa panas dan pengap saat masker digunakan dalam waktu lama.
Essential oils as the antibacterial substance in textiles are commonly demanded since they are easily found and have additional properties as relaxation therapy. This study aims to receive an antibacterial cloth using eucalyptus oil as a finishing substance gained from the leaves of Melaleuca leucadendra L. from a local industry (Perhutani Gundih, Central Java). The four types of cotton/polyester fabrics were prepared for finishing treatment with the bathing direct application method. They were 100% cotton, 100% polyester, 80%/20% polyester/cotton, and 65%/35% polyester/cotton. FTIR findings proved the existence of the eucalyptus main compound (α-pinene) in those four fabrics. Moreover, the antibacterial tests using S. aureus cultivation showed that only 100% polyester-treated fabric did not obtain antibacterial properties because the diameter of bacterial inhibition was zero millimeters. The other three fabrics potentially have antibacterial properties even if they did not gain a high diameter inhibitor zone.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.