Problems that occur in concrete buildings in the coastal environment of concrete damage caused by degradation of concrete that interacted seawater. Real damage caused by seawater, consists of 3 (three) parts: submerged concrete part, concrete part affected by tidal seawater and part of the concrete affected by seawater splashing. The concrete damage discussed in this research is the mechanical degradation of concrete due to the intrusion of seawater in the submerged seawater. Damage can occur in concrete due to the reaction between aggressive seawater that is intruded into the concrete and compounds in the concrete that causes the concrete lose some of its mass, its strength, and stiffness and also accelerate the weathering process. The results of this study indicate that the reduction of compressive strength of concrete due to the intrusion of seawater tends to show a logarithmic graph. Concrete compressive strength will lose by 50% when the concrete is soaked seawater for 19,031 days. Normal quality concrete f’c = 25 MPa undergoes mechanical degradation due to seawater intrusion, in this case, the compressive strength of concrete is 12,063 % when soaked 28 days and 16,809 % when soaked 90 days.
The infiltration capacity will decrease if the number of infiltration fields decreases. This results in increased surface runoff or inundation. The planning concept that creates a groundwater infiltration area in drainage will be able to reduce inundation in drainage. Pore Cylinder Hole is a water infiltration method by increasing water absorption in the soil. The aim of the study was to determine the effect of pore-hole spacing on infiltration capacity in pore-cylindrical drainage and to determine how much infiltration discharge due to variations in hole spacing using three levels of pore cylinder heights. This research was conducted using a pore-cylindrical drainage model and spacing the biopore holes and flowing water on the drainage surface. From the results of this study, it was found that the effect of the hole distance on the infiltration discharge, the closer the hole to the pore cylinder, the greater the infiltration discharge that occurs, it can be proven from the results of analysis of research data, for a flow rate of 400 cm 3 / sec, Qf = 35.1 cm 3 / sec. for spacing of holes 16 cm); Qf = 31.9cm 3 / s (to describe 32 cm holes); and Qf = 3.13cm 3 / s (for spacing of 16 cm holes).
Saluran peluncur pada bendungan membawa aliran dari ujung hilir saluran transisi sampai peredam energi. Kecepatan aliran yang tinggi dan tekanan yang rendah pada saluran peluncur dapat menimbulkan kavitasi dan aliran getar. Pelimpah memiliki kemiringan curam berisiko terhadap munculnya perilaku hidraulika yaitu kavitasi, kavitasi yang tidak dihilangkan dapat membahayakan permukaan dasar saluran akibat terjadinya gerusan. Tujuan penelitian ini untuk mengetahui nilai indeks kavitasi dan klasifikasi nilai indeks kavitasi. Metode penelitian ini digunakan jenis penelitian deskriptif kuantitatif menggunakan analisis data sekunder sebagai sumber data utama, dengan cara perbandingan menggunakan data lapangan dengan pemodelan aplikasi HEC-RAS. Hasil nilai indeks kavitasi yang terjadi disaluran peluncur bervariasi setiap bulannya dipengaruhi oleh debit, kecepatan, kedalaman air dan temperatur, dengan cara manual nilai indeks kavitasi terbesar 180,70 terjadi pada bulan Maret debit q5 dan terkecil 4,54 terjadi pada bulan Februari pada debit q350, Untuk cara komputasi nilai indeks kavitasi terbesar 249,42 pada bulan Januari debit Q5, dan terkecil 8,74 pada bulan Februari debit Q350, dan Klasifikasi nilai indeks kavitasi diperoleh bahwa nilai indeks kavitasi lebih besar dari 1 (σ>1) masuk dalam level 1 yang berarti bahwa tidak terjadi aliran negatif atau saluran peluncur masuk dalam kategori aman terhadap kavitasi. Saluran peluncur pada bendungan membawa aliran dari ujung hilir saluran transisi sampai peredam energi. Kecepatan aliran yang tinggi dan tekanan yang rendah pada saluran peluncur dapat menimbulkan kavitasi dan aliran getar. Pelimpah memiliki kemiringan curam berisiko terhadap munculnya perilaku hidraulika yaitu kavitasi, kavitasi yang tidak dihilangkan dapat membahayakan permukaan dasar saluran akibat terjadinya gerusan. Tujuan penelitian ini untuk mengetahui nilai indeks kavitasi dan klasifikasi nilai indeks kavitasi. Metode penelitian ini digunakan jenis penelitian deskriptif kuantitatif menggunakan analisis data sekunder sebagai sumber data utama, dengan cara perbandingan menggunakan data lapangan dengan pemodelan aplikasi HEC-RAS. Hasil nilai indeks kavitasi yang terjadi disaluran peluncur bervariasi setiap bulannya dipengaruhi oleh debit, kecepatan, kedalaman air dan temperatur, dengan cara manual nilai indeks kavitasi terbesar 180,70 terjadi pada bulan Maret debit q5 dan terkecil 4,54 terjadi pada bulan Februari pada debit q350, Untuk cara komputasi nilai indeks kavitasi terbesar 249,42 pada bulan Januari debit Q5, dan terkecil 8,74 pada bulan Februari debit Q350, dan Klasifikasi nilai indeks kavitasi diperoleh bahwa nilai indeks kavitasi lebih besar dari 1 (σ>1) masuk dalam level 1 yang berarti bahwa tidak terjadi aliran negatif atau saluran peluncur masuk dalam kategori aman terhadap kavitasi.
Salah satu tantangan yang dihadapi para ahli teknologi beton adalah bagaimana memanfaatkan limbah industri sebagai bahan tambah atau substitusi parsial pada beton normal. Dalam hal ini, para ahli mengkaji dan meneliti tentang pemanfaatan limbah industri yang ada agar dapat dimanfaatkan terutama bahan limbah abu ampas tebu industri pabrik gula. Hal ini menjadi salah satu dari sekian solusi penanganan limbah yang ada dimasyarakat. Tujuan dari penelitian ini adalah untuk mengetahui pengaruh substitusi abu ampas tebu terhadap agregat halus pada beton normal secara fisik dan mekanik. Bahan yang digunakan dalam penelitian ini terdiri dari semen Portland Composit Cement (PCC), agregat halus Sungai Je’ne’berang Gowa, agregat kasar yang berasal dari batu pecah Bili-Bili dan air PDAM dan material limbah abu ampas tebu sebagai substitusi agregat halus berasal dari Pabrik Gula Kabupaten Takalar, Provinsi Sulawesi Selatan. Alat yang digunakan pada penelitian ini sebelumnya telah diperiksa kondisi dan kemampuannya serta telah dikalibrasi terlebih dahulu. Benda uji silinder dibuat dengan cara memasukkan beton segar dari molen ke dalam cetakan silinder ukuran 15 cm x 30 cm yang telah diolesi minyak pelumas. Pengisian ini dilakukan secara bertahap, yaitu tiap sepertiga bagian dilakukan penumbukan dengan tongkat baja sebanyak ± 25 kali. Setelah 24 jam, cetakan dibuka kemudian dilakukan perawatan dengan direndam di dalam bak air selama 28 hari. Benda uji beton normal sebanyak 9 sampel dan benda uji yang disubstitusi abu ampas tebu sebanyak 9 sampel. Berdasarkan hasil penelitian didapatkan nilai berat volume beton untuk komposisi pencampuran ampas tebu 8% yaitu 701,41 kg/m3, 10% yaitu 701,41 kg/m3 dan 12% yaitu 690,10 kg/m3 dari ketiga komposisi tersebut diperoleh berat volume beton yang maksimal yaitu komposisi pencampuran ampas tebu 12%.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.