The chance to move from 2D to 3D approach in the design of the electrical machines is made possible by the availability of Soft Magnetic Composites (SMC), iron based powders, insulated and pressed to realize shapes otherwise impossible with the traditional lamination sheets technology. Some commercial products are available on the market as “ready to press” powders, which presents good magnetic and energetic properties but are sometimes weak under the mechanical point of view; other products aim at improving this aspect but with considerable process complications and relative cost. The experience of the Authors in the realization of bonded magnets with the adoption of selected organic resins has been partly transferred in the research field of the SMC in order to investigate the possibility to obtain good mechanical properties maintaining the magnetic characteristics of the Insulated Iron Powder Compounds (I.I.P.C.) taken as reference. The paper presents the activity that has been carried out in the realization of SMC mixing iron powders and phenolic resin, in different weight percentages and mold pressures. The obtained results are considered satisfactory under the point of view of the compromise between magnetic and mechanical properties, considering also that the required productive process is simpler. The comparison of the obtained results with those related to commercial products encourages to carry on the research, also because of the reduced cost of the proposed SMC at parity (or better) performance.

No abstract

No abstract

The interest around the adoption of Soft Magnetic Composite materials (SMC) in the realization of electric machines, or parts of electric machines, is continuously increasing. The main reason lies on the opportunity to realize magnetic circuits following a 3D design procedure, which is not allowed with the adoption of the traditional lamination sheets. This is not the only reason, as a lot of research is being carried out on the losses distribution in the magnetic material, particularly as function of the frequency. In this paper different iron powders have been analyzed to investigate the impact of the granulometry on the SMC performance; in particular the grain size and the oxygen content have been considered variable parameters. The materials, prepared, compacted and tested in our laboratories, have been characterized to obtain the magnetic characteristic and information about the iron losses.

In electrical machines, laminated steels are commonly adopted as soft magnetic materials, while for permanent magnets, sintered ferrites and NdFeB are the most common solutions. On the other hand, the growing demand for volume reduction with the increment of efficiency leads to the necessity of exploring other magnetic materials able to face the challenge better than the traditional ones. Bonded magnets have been used to replace sintered magnets, obtaining a better use of space and particular magnetic properties. Instead, for the magnetic circuit, Soft Magnetic Composites (SMC) allow realizing very complex magnetic design (3D path for flux) with iron loss reduction at medium-high frequencies, especially for the eddy currents loss contribution. On the other hand, SMC materials have such drawbacks as low mechanical properties and high hysteresis losses. For this reason, in this work, different studies considering several variables have been carried out. SMCs were produced through a moulding process; inorganic and organic layers to cover ferromagnetic particles were used, adopting different coating processes. Particular tests have been performed for a quicker and more indicative overview of the materials obtained. The single sheet tester (SST) is easier than traditional toroidal methods; on the other hand, the multiplicity of variables affects the SMC materials and their process. For this reason, coercivity and conductibility tests permit rapid measurement and provide a direct classification of the produced SMCs, providing the main information needed to select suitable materials. Results highlighted that choosing the more appropriate SMC material is possible after using these simple preliminary tests. After these tests, it was possible to argue that with 0.2 wt% of phenolic resin as the organic layer (and compaction pressure of 800 MPa), it is possible to produce a good SMC. On the other hand, the SMC with 0.2 wt% of epoxy resin (and compaction pressure of 800 MPa) gives a minor coercivity value. Additionally, despite the SMC with the inorganic layer, 0.2 wt% of nano-ferrites showing the best coercivity values (specifically for vacuum treatment at 600 °C), their resistivity was unsatisfactory.

During the past 50 years, the aim to reduce the eddy current losses in magnetic cores to a minimum led to the formulation of new materials starting from electrically insulated iron powders, today called Soft Magnetic Composites (SMC). Nowadays, this promising branch of materials is still held back by the mandatory tradeoff between energetic, electrical, magnetic, and mechanical performances. In most cases, the research activity focuses on the deposition of an insulating/binding layer, being one of the critical points in optimizing the final composite. This insulation usually is achieved by either inorganic or organic layer constituents. The main difference is the temperature limit since most inorganic materials typically withstand higher treatment temperatures. As a result, the literature shows many materials and process approaches, each one designed to meet a specific application. The present work summarizes the recent advances in state of the art, analyzing the relationship among material compositions and magnetic and mechanical properties. Each coating shows its own processing sets, which vary from simple mechanical mixing to advanced chemical methods to metallurgical treatments. From state of the art, Aluminum coatings are characterized by higher current losses and low mechanical properties. In contrast, higher mechanical properties are obtained by adopting Silicon coatings. The phosphates coatings show the best-balanced overall properties. Each coating type was thoroughly investigated and then compared with the literature background highlighting. The present paper thus represents a critical overview of the topic that could serve as a starting point for the design and development of new and high-performing coating solutions for SMCs. However, global research activity continuously refines the recipes, introducing new layer materials. The following steps and advances will determine whetherthese materials breakthrough in the market.

Electrical machines cover a very wide range of applications in many industrials sectors and the research to improve the performance of those applications is recently leading to the development of new solutions. Those devices are generally equipped with magnetic circuits made of laminated ferromagnetic steel, but in the last decade, new magnetic materials have been developed to realise magnetic circuits: Soft Magnetic Composites (SMC). The Authors have investigated SMCs with organic layer obtained through the adoption of phenolic and epoxy resins; in previous research activities several mixture compositions have been produced and analysed with different percentages of binder and compacting pressures. Promising results regarding magnetic and mechanical performances have been obtained using a very low binder content. The paper aims to investigate the lower limit of the binder to be used, still keeping good mechanical properties. Appropriate magnetic tests have been performed on toroidal specimens: good magnetic characteristics have been obtained, maintaining on the other side proper mechanical strength.

In the field of electrical machines, the actual research activities mainly focus on improving the energetic aspects; for this reason, new magnetic materials are currently investigated and proposed, supporting the design and production of magnetic cores. The innovative aspects are related to both hard and soft magnetic materials. In the case of permanent magnets, the use of NdFeB bonded magnets represents a good solution in place of ferrites. For what concerns the soft magnetic materials, the adoption of Soft Magnetic Composites (SMCs) cores permits significant advantages compared to the laminated sheets, such as complex geometries and reduced eddy currents losses. SMC materials are ferromagnetic grains covered with an insulating layer that can be of an organic or inorganic type. The proposed study focuses on the impact of the particle size and distribution on the final material properties. The original powder was cut into three different fractions, and different combinations have been prepared, varying the fractions percentages. The magnetic and energetic properties have been evaluated in different frequency ranges, thus ranking the best combinations. The best specimens were then tested to evaluate the mechanical performances. The preliminary results are promising, but deeper analysis and tests are required to refine the selection and evaluate the improvements against the original composition taken as a reference.