Nanofluid flooding, as a new technique to enhance oil recovery, has recently aroused much attention. The current study considers the performance of a novel iron-carbon nanohybrid to EOR. Carbon nanoparticles was synthesized via the hydrothermal method with citric acid and hybridize with iron (Fe3O4). The investigated nanohybrid is characterized by its rheological properties (viscosity), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR) analysis. The efficiency of the synthetized nanoparticle in displacing heavy oil is initially assessed using an oil–wet glass micromodel at ambient conditions. Nanofluid samples with various concentrations (0.05 wt % and 0.5 wt %) dispersed in a water base fluid with varied salinities were first prepared. The prepared nanofluids provide high stability with no additive such as polymer or surfactant. Before displacement experiments were run, to achieve a better understanding of fluid–fluid and grain–fluid interactions in porous media, a series of sub-pore scale tests—including interfacial tension (IFT), contact angle, and zeta potential—were conducted. Nanofluid flooding results show that the nanofluid with the medium base fluid salinity and highest nanoparticle concertation provides the highest oil recovery. However, it is observed that increasing the nanofluid concentration from 0.05% to 0.5% provided only three percent more oil. In contrast, the lowest oil recovery resulted from low salinity water flooding. It was also observed that the measured IFT value between nanofluids and crude oil is a function of nanofluid concentration and base fluid salinities, i.e., the IFT values decrease with the increase of nanofluid concentration and base fluid salinity reduction. However, the base fluid salinity enhancement leads to wettability alteration towards more water-wetness. The main mechanisms responsible for oil recovery enhancement during nanofluid flooding is mainly attributed to wettability alteration toward water-wetness and micro-dispersion formation. However, the interfacial tension (IFT) reduction using the iron-carbon nanohybrid is also observed but the reduction is not significant.

No abstract

We have evaluated several published models using induced polarization (IP) and nuclear magnetic resonance (NMR) measurements for the estimation of permeability of hydrocarbon reservoir samples. IP and NMR measurements were made on 30 samples (clean sands and sandstones) from a Persian Gulf hydrocarbon reservoir. We assessed the applicability of a mechanistic IP-permeability model and an empirical IP-permeability model recently proposed. The mechanistic model results in a broader range of permeability estimates than those measured for sand samples, whereas the empirical model tends to overestimate the permeability of the samples that we tested. We also evaluated an NMR permeability prediction model that is based on porosity [Formula: see text] and the mean of the log transverse relaxation time ([Formula: see text]). This model provides reasonable permeability estimations for the clean sandstones that we tested but relies on calibrated parameters. We also examined an IP-NMR permeability model, which is based on the peak of the transverse relaxation time distribution, [Formula: see text] and the formation factor. This model consistently underestimates the permeability of the samples tested. We also evaluated a new model. This model estimates the permeability using the arithmetic mean of log transverse NMR relaxation time ([Formula: see text]) and diffusion coefficient of the pore fluid. Using this model, we improved estimates of permeability for sandstones and sand samples. This permeability model may offer a practical solution for geophysically derived estimates of permeability in the field, although testing on a larger database of clean granular materials is needed.

No abstract

Smart waterflooding is one of the most practical emerging methods of enhanced oil recovery in carbonate reservoirs. In this study, the effect of salt type and its concentration in smart water on oil recovery from a carbonate reservoir rock is investigated. A series of experimental measurements, including zeta potential (ZP), interfacial tension (IFT), and contact angle (CA), were conducted to examine the effect of ions on the oil/brine/rock interaction. IFT, ZP, and CA were also used as screening methods to select effective solutions for flooding experiments. The results of the study show that synthesized brines containing sodium acetate and potassium acetate salts have a significant effect on the reduction of IFT; however, rock surface wettability due to such brines is insignificant. The presence of organic salts in the injected water can alter the properties of the fluid and rock surface, leading to improved oil recovery. The salts can reduce the interfacial tension between the oil and water phases, making it easier for the water to displace and mobilize trapped oil. This effect is particularly beneficial in reservoirs with high oil–water interfacial tension as it enhances the capillary forces and improves the sweep efficiency. Smart water with sodium acetate (MSW.NaOAc) caused a 7% increase in oil production in the tertiary injection process due to IFT and CA reduction. The secondary injection of MSW.NaOAc led to an oil production efficiency of 76%, which is 10% higher than that of the secondary injection of seawater (SW), confirming the effectiveness of acetate ions in enhancing oil recovery. Doubling the concentration of sulfate ions in modified SW (MSW.NaOAc.2S) caused a 19% increase in oil production in tertiary injections after SW flooding. The secondary injection of MSW.NaOAc.2S produced a 13% increase in the recovery factor compared to SW flooding in the secondary mode. The main driving mechanism for oil mobilization was found to be wettability alteration, which is supported by the analyses of CA and ZP. This study confirms that the salt type and concentration present in a brine solution play a vital role in the movement of trapped oil in carbonate reservoirs.