In some areas, the estimation of static corrections for land seismic data is a critical step of the processing workflow. It often requires the execution of additional surveys and data analyses. Surface waves (SWs) in seismic records can be processed to extract local dispersion curves (DCs) that can be used to estimate near-surface S-wave velocity models. Here we focus on the direct estimation of time-average S-wave velocity models from SW DCs without the need to invert the data. Time-average velocity directly provides the value of one-way time, given a datum plan depth. The method requires the knowledge of one 1D S-wave velocity model along the seismic line, together with the relevant DC, to estimate a relationship between SW wavelength and investigation depth on the time-average velocity model. This wavelength/depth relationship is then used to estimate all the other time-average S-wave velocity models along the line directly from the DCs by means of a data transformation. This approach removes the need for extensive data inversion and provides a simple method suitable for industrial workflows. We tested the method on synthetic and field data and found that it is possible to retrieve the time-average velocity models with uncertainties less than 10% in sites with laterally varying velocities. The error on one-way times at various depths of the datum plan retrieved by the time-average velocity models is mostly less than 5 ms for synthetic and field data.
Elastic full-waveform inversion (FWI) is a powerful tool for high-resolution subsurface multi-parameter characterization. However, 3D FWI applied to land data for near-surface applications is particularly challenging, since the seismograms are dominated by highly energetic, dispersive, and complex-scattered surface waves (SWs). In these conditions, a successful deterministic FWI scheme requires an accurate initial model. This study, primarily focused on field data analysis for 3D applications, aims at enhancing the resolution in the imaging of complex shallow targets, by integrating devoted SW analysis techniques with a 3D spectral-element-based elastic FWI. From dispersion curves (DCs), extracted from seismic data recorded over a sharp-interface shallow target, we built different initial S-wave (VS) and P-wave (VP) velocity models (laterally homogeneous and laterally variable), using a specific data-transform. Starting from these models, we carry out 3D FWI tests on synthetic and field data, using a relatively straightforward inversion scheme. The field data processing before FWI consists of bandpass filtering and muting of noisy traces. During FWI, a weighting function is applied to the far-offset traces. We test both 2D and 3D acquisition layouts, with different positions of the sources and variable offsets. The 3D FWI workflow enriched the overall content of the initial models, allowing a reliable reconstruction of the shallow target, especially when using laterally variable initial models. Moreover, a 3D acquisition layout guaranteed a better reconstruction of the target’s shape and lateral extension. In addition, the integration of model-oriented (preliminary monoparametric FWI) and data-oriented (time-windowing) strategies into the main optimization scheme has granted further improvement of the FWI results.
Exploration seismic surveys in hard-to-access areas such as foothills and forests are extremely challenging. The Multiphysics Exploration Technologies Integrated System (METIS) research project was initiated to design an exploration system, facilitating the acquisition in these areas by delivering the receivers from the sky using unmanned aerial vehicles. Air dropping of the sensors in vegetated areas results in an irregular geometry for the acquisition. This irregularity can limit the application of conventional surface wave methods. We have developed a surface wave workflow for estimating the S-wave velocity ( VS) and P-wave velocity ( VP) models and that supports the irregular geometry of the deployed sources and receivers. The method consists of a multimodal surface wave tomography (SWT) technique to compute the VS model and a data transform method (the wavelength/depth [W/D] method) to determine the Poisson’s ratio and VP model. We applied the method to the METIS’s first pilot records, which were acquired in the forest of Papua New Guinea. Application of SWT to the data resulted in the first 90 m of the VS model. The W/D method provided the Poisson’s ratio averaged over the area and the VP model between 10 and 70 m from the surface. The impact of the acquisition scale and layout on the resolution of the estimated model and the advantages of including the higher modes of surface waves in the tomographic inversion are assessed in detail. The presence of shots from diverse site locations significantly improves the resolution of the obtained model. Including the higher modes enhances the data coverage and increases the investigation depth.
SUMMARY The analysis of surface wave dispersion curves (DCs) is widely used for near-surface S-wave velocity (VS) reconstruction. However, a comprehensive characterization of the near-surface requires also the estimation of P-wave velocity (VP). We focus on the estimation of both VS and VP models from surface waves using a direct data transform approach. We estimate a relationship between the wavelength of the fundamental mode of surface waves and the investigation depth and we use it to directly transform the DCs into VS and VP models in laterally varying sites. We apply the workflow to a real data set acquired on a known test site. The accuracy of such reconstruction is validated by a waveform comparison between field data and synthetic data obtained by performing elastic numerical simulations on the estimated VP and VS models. The uncertainties on the estimated velocity models are also computed.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.