During the last twenty years DBD plasma actuators have been known by their ability for boundary layer flow control applications. However, their usefulness is not limited to this application field, they also present great utility for applications within the field of heat transfer, such as a way to improve the aerodynamic efficiency of film cooling of gas turbine blades, or de-icing and ice formation prevention. Nevertheless, there is a relative lack of information about DBD's thermal characteristics and its heat generation mechanisms. This happens due to the extremely high electric fields in the plasma region and consequent impossibility of applying intrusive measurement techniques. Against this background, this work describes the physical mechanisms behind the generation of heat associated to the DBD plasma actuators operation. An experimental technique, based on calorimetric principles, was devised in order to quantify the heat energy generated during the plasma actuators operation. The influence of the dielectric thickness, as well as the dielectric material, were also evaluated during this work. The results were exposed and discussed with the purpose of a better understanding of the heat generation mechanisms behind the operation of DBD plasma actuators.

No abstract

Dielectric barrier discharge (DBD) plasma actuators have several applications within the field of active flow control. Separation control, wake control, aircraft noise reduction, modification of velocity fluctuations, or boundary layer control are just some examples of their applications. They present several attractive features such as their simple construction, very low mass, fast response, low power consumption, and robustness. Besides their aerodynamic applications, these devices have also possible applications within the field of heat transfer, for example film cooling applications or ice formation prevention. However, due to the extremely high electric fields in the plasma region and consequent impossibility of applying classic intrusive techniques, there is a relative lack of information about DBDs thermal characteristics. In an attempt to overcome this scenario, this work describes the thermal behavior of DBD plasma actuators under different flow conditions. Infra-red thermography measurements were performed in order to obtain the temperature distribution of the dielectric layer and also of the exposed electrode. During this work, we analyzed DBD plasma actuators with different dielectric thicknesses and also with different dielectric materials, whose thermal behavior is reported for the first time. The results allowed to conclude that the temperature distribution is not influenced by the dielectric thickness, but it changes when the actuator operates under an external flow. We also verified that, although in quiescent conditions the exposed electrode temperature is higher than the plasma region temperature, the main heat energy dissipation occurs in the dielectric, more specifically in the plasma formation region.

Plasma actuators are simple devices with a wide variety of applications within the flow control and heat transfer fields. These electronic devices comprise two electrodes, asymmetrically mounted, separated by a dielectric layer. When these devices are supplied with an AC high voltage signal, a plasma discharge is generated on the top of the dielectric layer, which leads to the ionization of the adjacent air that, in turn, is accelerated downstream due to the presence of the electric field. Therefore, these devices pull the adjacent air towards the surface and blow it in a tangential direction to the surface [1][2][3]. This phenomenon allows us to manipulate the flow and makes these devices very appealing for applications within the active

Plasma actuators are electronic devices commonly used for active flow control. These devices have been shown to be effective in a wide variety of fluids engineering applications. In order to increase the efficiency of these devices, the combination of micro exposed electrodes with stair-shaped dielectric layers is proposed. The flow induced by micro and macro stair-shaped plasma actuators is experimentally evaluated and its mechanical efficiency is estimated. Furthermore, durability tests are performed in order to show that stair-shaped dielectric layers also allow to increase the device lifetime. It is shown that by combining micro exposed electrodes with stair-shaped dielectric layers it is possible to achieve mechanical efficiencies 8 times greater than in a conventional macro actuator. In addition, degradation tests demonstrate that stair-shaped dielectric layers degrade slower and lead to an increased lifetime.

The quest for increased performance in the aeronautical and aerospace industries has provided the driving force and motivation for the research, investigation, and development of advanced ceramics. Special emphasis is therefore attributed to the ability of fine ceramics to fulfill an attractive, extreme, and distinguishing combination of application requirements. This is impelled by ensuring a suitable arrangement of thermomechanical, thermoelectric, and electromechanical properties. As a result, the reliability, durability, and useful lifetime extension of a critical structure or system are expected. In this context, engineered ceramic appliances consist of three main purposes in aeronautical and aerospace fields: thermal protection systems (TPS), thermal protection barriers (TBC), and dielectric barrier discharge (DBD) plasma actuators. Consequently, this research provides an extensive discussion and review of the referred applications, i.e., TPS, TBC, and DBD, and discusses the concept of multifunctional advanced ceramics for future engineering needs and perspectives.

Dielectric Barrier Discharge plasma actuators are simple devices with great potential for active flow control applications. They have very interesting features which have made them a topic of interest for many researchers, for instance they present very low mass, fast response time, low cost, easy implementation and they are fully electronic with no moving parts. The dielectric material used in the construction of these devices present an important role in their performance. The variety of dielectrics studied in the literature is very restrict and the majority of the authors make use of Kapton, Teflon, Macor ceramic or PMMA. Furthermore, several authors reported difficulties in the durability of the dielectric layer when actuators operate at high levels of voltage and frequency. Considering this background, the present study focus on the experimental testing of alternative dielectric materials which can be used for DBD plasma actuators fabrication. Considering this, plasma actuators with dielectric layers made of Poly-Isobutylene rubber, Poly-Lactic acid and Acetoxy Silicon were experimentally tested. Although these dielectric materials are not commonly used in plasma actuators, their values of dielectric strength and dielectric permittivity indicate they can be good solutions. The plasma actuators facbricated with these alternative dielectric materials were experimentally analysed in terms of electrical characteristics and induced flow velocity, and the obtained results were compared with an actuator made of Kapton which is, currently, the most common dielectric material for plasma actuators. The effectiveness of the actuators was estimated and the advantages and disadvantages of the use of each dielectric material were discussed.

No abstract