Thin film Cu(In,Ga)Se2 (CIGS)-based solar cells with relatively high efficiency and low material usage might become a promising alternative for crystalline silicon technology. The most challenging task nowadays is to decrease the PV module fabrication costs by application of easily scalable industrial process. One of the possible solutions is the usage of magnetron sputtering system for deposition of all structures applied in CIGS-based photovoltaic device. The main object of these studies was fabrication and characterization of thin films deposited by sputtering technique. Structural and electrical properties of the sputtered films were analyzed using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray Powder Diffraction (XRD), and four-point probe resistivity measurements. The presented findings revealed technological parameters for which sheet resistance of molybdenum (Mo) back contact decreased up to 0.3 Ω/□ and to even 0.08 Ω/□ in case of aluminum layer. EDS analysis provided evidence for the appropriate stoichiometry of CIGS absorber (with CGI and GGI equal to 0.96 and 0.2, respectively). XRD characterization confirmed high-quality chalcopyrite polycrystalline structure of Cu(In,Ga)Se2 film fabricated at relatively low substrate temperature of 400 °C. Characteristic XRD peaks of hexagonal-oriented structures of sputtered CdS and i-ZnO layers were noticed.
Dye-sensitized solar cells (DSSC) of third generation photovoltaic technology, are nowadays one of the most investigated due to possibility to apply ecological and natural materials (dyes) such as alizarin. This paper reports the influence of electrode immersion time on alizarinbased dye-sensitized solar cells performance. The absorption spectra of alizarin dye were measured in the range of 300-800 nm. Fully structured dye-sensitized cells of working area equal to 0.8 cm 2 have been fabricated in the sandwich way using four different immersion times of the TiO2 electrodes: 10', 40', 1 h, 24 h. The high-performance EL-HPE electrolyte was instilled into the space between electrodes. Current-voltage (I-V) dark and illuminated characteristics have been measured using solar light simulator. Solar cells characterization was carried out under standard test conditions. The solar irradiance was set at 100 mW/cm 2 and temperature of the module was maintained at 25°C. Characteristic parameters of the fabricated cells were determined on the basis of measured I-V curves. Series resistances were extracted from I-V characteristics at an open circuit voltage using first order derivatives. It was found that 60 minutes of electrode immersion in dye solution is sufficient to obtain appropriate stage of the dye adsorption.
Since early 1990s dye-sensitized solar cells (DSSC) has been developed by many research groups all over the World. This paper presents a review of researches focusing on photosensitizer influence on DSSC efficiency. Variety of dye substance has been analyzed. The highest efficiency around 11.2% has been noted for ruthenium-based DSSC devices. Natural dyes allowed to reach 4.6%. The most metal-free organic dyes resulted in efficiency ranged from 5% to 9%, however, some of them (e.g. Y123) allowed to obtain devices with efficiencies equal to 10.3%. Co-sensitization is the new approach which results in efficiencies up to 14.3%.
Dye-sensitized solar cells (DSSCs) were fabricated using a photoelectrode covered by a porous layer of titanium dioxide, platinum counter electrode, iodide/triiodide electrolyte and three different dyes: phenylfluorone (PF), pyrocatechol violet (PCV) and alizarin (AL). After the adsorption of the dyes on the mesoporous TiO2 layer, the measurement of absorption spectra of all the tested dyes revealed a significant broadening of the absorption range. The positions of highest occupied molecular orbital (HOMO) and lowest occupied molecular orbital (LUMO) levels of dye molecules were determined, indicating that all three dyes are good candidates for light harvesters in DSSCs. The cells were tested under simulated solar light, and their working parameters were determined. The results showed that the implementation of the back reflector layer made of BaSO4 provided an improvement in the cell efficiency of up to 17.9% for phenylfluorone, 60% for pyrocatechol violet and 21.4% for alizarin dye.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.