Abstract. In this paper, a mathematical model for modelling the solar radiation components and photovoltaic arrays power outputs from arbitrarily oriented photovoltaic panel has been presented. Base on the model electrical power prediction of the photovoltaic system in realistic local condition has been presented and compared with experimental measurement. The results show the effectiveness of the proposed model, which provides tools to better understand the performance and reliability as well as decision-making tool in designing of a hybrid renewable energy base power generation system. It has been shown that base on the model prediction, the efficiency and possible failures of the system can be found which are important from the technical and economical point of view.
Abstract. This article discusses the problems related with the cold production, i.e. energy efficiency of the process. The idea of solar cooling systems has been presented as the solution of the problem of big electricity demand. The paper discusses the principle of the operation of absorption chillers. Disadvantages and advantages of the solar cooling systems were discussed. The installation for manufacturing high-temperature heat based on solar collectors and concentrator of solar radiation constructed in AGH in Cracow has been presented. This installation is a first stage of projected, complete solar cooling system. The special attention is paid to the dedicated solar high-temperature heat receiver as a most important element of the system. The achieved values of temperature, power and efficiency depending on the working medium flow has been presented and discussed. The intensity of solar radiation during the measurements has been taken into account. Two versions of heat receiver were investigated: non-insulated and insulated with mineral wool. The obtained efficiency of the heat receiver (less than 30%) is not satisfactory but possibility of improvements exist.
Abstract. The article presents the results of experimental and computer simulations studies of the high temperature heat receiver working in the concentrated solar radiation system. In order to study the radiation absorption process and heat exchange, the two types of computer simulations were carried out. The first one was used to find the best location for absorber in the concentrating installation. Ray Tracing Monte Carlo (RTMC) method in Trace Pro software was used to perform the optical simulations. The results of these simulations were presented in the form of the solar radiation distribution map and chart. The data obtained in RTMC simulations were used as a second type boundary conditions for Computational Fluid Dynamics (CFD) simulations. These studies were used to optimize the internal geometry of the receiver and also to select the most effective flow parameters of the working medium. In order to validate the computer simulations, high temperature heat receiver was tested in experimental conditions. The article presents the results of experimental measurements in the form of temperature, radiation intensity and power graphs. The tests were performed for varied flow rate and receiver location. The experimental and computer simulation studies presented in this article allowed to optimize the configuration of concentrating and heat receiving system.
Przedstawiono znaczenie rozwoju technologii chłodzenia z wykorzystaniem energii promieniowania słonecznego. Systemy takie z reguły używają dodatkowego źródła ciepła pozwalającego osiągnąć temperaturę efektywnej pracy chłodziarki absorpcyjnej. W tym celu w wielu rozwiązaniach stosowane są dodatkowe źródła ciepła w postaci podgrzewaczy elektrycznych, gazowych i innych czyli używają-cych energię nieodnawialną. W krajach południowych możliwa jest praca systemu chłodniczego wyłącznie w oparciu o energię odnawialną przy wykorzystaniu odpowiednio dużych zestawów kolektorów próżniowych. Jednakże w Polsce instalacje kolektorów słonecznych bazują najczęściej na kolektorach płaskich i nie posiadają tak dużej powierzchni. Dlatego przewidziano układ bazujący na kolektorach płaskich z dogrzewaniem czynnika roboczego w postaci koncentratora promieniowania słonecznego. W pracy przedstawiono opis stanowiska badawczego oraz wybrane wyniki badań pracy takiego hybrydowego układu. Wykonano modelowanie pracy układu hybrydowego w celu opisu temperatury na wyjściu z kolektora dla naturalnej zmienności godzinowej natężenia promieniowania słonecznego oraz dla kilku wybranych prędkości przepływu medium roboczego. Wykazano, że możliwy jest wystarczająco dokładny opis za pomocą uproszczonego modelu matematycznego koncentratora, jednakże wymagana jest znajomość parametrów technicznych koncentratora (m.in. sprawności odbiornika ciepła, sprawności koncentracji promieniowania i inne). W wielu przypadkach praktycznych dokładne określenie tych wielkości może być trudne. Dlatego przeprowadzono analizę czułości modelu na niepewności tych parametrów.Słowa kluczowe: chłodzenie słoneczne, koncentracja promieniowania słoneczne-go, kolektory słoneczne, chłodziarka absorpcyjna, natężenie promieniowania sło-necznego
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.