The dispersion microstructure and rheological properties of aqueous sulfonated cellulose nanocrystal (CNC) suspensions have been investigated. Between 3.07 and 10.4 vol % the suspensions phase separated into liquid crystalline and isotropic domains. At 12.1 vol %, no isotropic phase was visible, and the samples had the fingerprint texture characteristic of a cholesteric liquid crystal. Below 35 °C, temperature had little influence on rheology and phase behavior. However, between 35 and 40 °C there was a significant change in both the fraction of isotropic phase and the rheological properties. In contrast to many lyotropic suspensions, the steady shear viscosity did not go through a maximum with increasing concentration. Maxima were observed for complex viscosity, storage modulus, and loss modulus at concentrations that appeared fully liquid crystalline. Time–concentration superposition was successful for the loss modulus but not the storage modulus. This suggests that the interface in biphasic samples affects the elastic relaxation but not the viscous response. At still higher concentrations, the fingerprint texture of the liquid crystal phase was absent, and the dispersions behaved as rheological gels.

This review highlights solvent systems that were designed to simultaneously address reaction, separation and recycling challenges.

In subsurface imaging and oil recovery where temperatures and salinities are high, it is challenging to design polymer-coated nanoparticles with low retention (high mobility) in porous rock. Herein, the grafting of poly­(2-acrylamido-2-methyl-1-propanesulfonic acid-co-acrylic acid) (poly­(AMPS-co-AA)) on magnetic iron oxide nanoparticles was sufficiently uniform to achieve low adsorption on model colloidal silica and crushed Berea sandstone in highly concentrated API brine (8% NaCl and 2% CaCl2 by weight). The polymer shell was grafted via amide bonds to an aminosilica layer, which was grown on silica-coated magnetite nanoparticles. The particles were found to be stable against aggregation in American Petroleum Institute (API) brine at 90 °C for 24 h. For IO nanoparticles with ∼23% polymer content, Langmuir adsorption capacities on colloidal silica and crushed Berea Sandstone in batch experiments were extremely low at only 0.07 and 0.09 mg of IO/m2, respectively. Furthermore, upon injection of a 2.5 mg/mL IO suspension in API brine in a column packed with crushed Berea sandstone, the dynamic adsorption of IO nanoparticles was only 0.05 ± 0.01 mg/m2, which is consistent with the batch experiment results. The uniformity and high concentration of solvated poly­(AMPS-co-AA) chains on the IO surfaces provided electrosteric stabilization of the nanoparticle dispersions and also weakened the interactions of the nanoparticles with negatively charged silica and sandstone surfaces despite the very large salinities.

Alginate fibers have found many applications such as the preparation of dressings to treat exuding wounds, drug delivery, enzyme immobilization, etc.; however, their use is limited due to poor mechanical properties. Cellulose nanocrystals (CNCs) were isolated from cotton and introduced into calcium alginate fibers with the goal of improving their strength and modulus. The isolated CNCs are elongated nanoparticles of crystalline cellulose with an average length of 130 nm with a standard deviation (s) of 63 nm, an average width of 20.4 nm (s = 7.8 nm), and an average height of 6.8 nm (s = 3.3 nm). The CNCs were mixed with an aqueous sodium alginate dope solution and wet spun into a CaCl(2) bath to form fibers. It was found that if the apparent jet stretch (ratio of the fiber draw velocity to extrusion velocity) is kept constant, addition of the nanocrystals reduces the tensile strength and modulus of the material; however, a small concentration of CNCs in the dope solution increases the tensile energy to break and enables an increase in the fiber spinning apparent jet stretch ratio by nearly 2-fold at up to 25% CNCs load; the maximum ratio of 4.6 is observed at 25 wt % CNC loading as compared to a maximum of 2.4 for the native alginate. Mechanical testing showed a 38% increase in tenacity and a 123% increase in tensile modulus with 10 wt % CNCs loading and an apparent jet stretch of 4.2. The data suggest that alignment of the nanocrystals in the composites is a key factor influencing the mechanical properties. CNCs have potential to become a biocompatible, renewable, and cost-effective solution to reinforce alginate fibers.