The synthesis of renewable fuels from abundant water or the greenhouse gas CO 2 is a major step toward creating sustainable and scalable energy storage technologies. In the last few decades, much attention has focused on the development of nonprecious metal-based catalysts and, in more recent years, their integration in solid-state support materials and devices that operate in water. This review surveys the literature on 3d metal-based molecular catalysts and focuses on their immobilization on heterogeneous solid-state supports for electro-, photo-, and photoelectrocatalytic synthesis of fuels in aqueous media. The first sections highlight benchmark homogeneous systems using proton and CO 2 reducing 3d transition metal catalysts as well as commonly employed methods for catalyst immobilization, including a discussion of supporting materials and anchoring groups. The subsequent sections elaborate on productive associations between molecular catalysts and a wide range of substrates based on carbon, quantum dots, metal oxide surfaces, and semiconductors. The molecule–material hybrid systems are organized as “dark” cathodes, colloidal photocatalysts, and photocathodes, and their figures of merit are discussed alongside system stability and catalyst integrity. The final section extends the scope of this review to prospects and challenges in targeting catalysis beyond “classical” H 2 evolution and CO 2 reduction to C 1 products, by summarizing cases for higher-value products from N 2 reduction, C x >1 products from CO 2 utilization, and other reductive organic transformations.

Lignocellulose is Earth's most abundant form of biomass and its valorisation to H 2 is a key objective for the generation of renewable fuels. Solar-driven photocatalytic reforming of lignocellulose to H 2 at ambient temperature offers a sustainable route towards this goal, but this reaction is currently limited to noble metal containing systems that operate with low activity under UV light. Here, we report the light-driven photoreforming of cellulose, hemicellulose and lignin to H 2 using semiconducting cadmium sulfide quantum dots in alkaline aqueous solution. We show that basic conditions cause these dots to become coated with oxide/hydroxide in situ, presenting a strategy to improve their photocatalytic performance. The system operates under visible light, is stable beyond 6 days and is even able to reform unprocessed lignocellulose, such as wood and paper, under solar irradiation at room temperature, presenting an inexpensive route to drive aqueous proton reduction to H 2 through waste biomass oxidation.

Carbon quantum dots (CQDs) are established as excellent photosensitizers in combination with a molecular catalyst for solar light driven hydrogen production in aqueous solution. The inexpensive CQDs can be prepared by straightforward thermolysis of citric acid in a simple one-pot, multigram synthesis and are therefore scalable. The CQDs produced reducing equivalents under solar irradiation in a homogeneous photocatalytic system with a Ni-bis(diphosphine) catalyst, giving an activity of 398 μmolH2 (gCQD)(-1) h(-1) and a "per Ni catalyst" turnover frequency of 41 h(-1). The CQDs displayed activity in the visible region beyond λ > 455 nm and maintained their full photocatalytic activity for at least 1 day under full solar spectrum irradiation. A high quantum efficiency of 1.4% was recorded for the noble- and toxic-metal free photocatalytic system. Thus, CQDs are shown to be a highly sustainable light-absorbing material for photocatalytic schemes, which are not limited by cost, toxicity, or lack of scalability. The photocatalytic hybrid system was limited by the lifetime of the molecular catalyst, and intriguingly, no photocatalytic activity was observed using the CQDs and 3d transition metal salts or platinum precursors. This observation highlights the advantage of using a molecular catalyst over commonly used heterogeneous catalysts in this photocatalytic system.

With over 8 billion tons of plastic produced since 1950, polymers represent one of the most widely usedand most widely discardedmaterials. Ambient-temperature photoreforming offers a simple and low-energy means for transforming plastic waste into fuel and bulk chemicals but has previously only been reported using precious-metal- or Cd-based photocatalysts. Here, an inexpensive and nontoxic carbon nitride/nickel phosphide (CN x |Ni2P) photocatalyst is utilized to successfully reform poly­(ethylene terephthalate) (PET) and poly­(lactic acid) (PLA) to clean H2 fuel and a variety of organic chemicals under alkaline aqueous conditions. Ni2P synthesized on cyanamide-functionalized carbon nitride is shown to promote efficient charge separation and catalysis, with a photostability of at least 5 days. The real-world applicability of photoreforming is further verified by generating H2 and organics from a selection of nonrecyclable wasteincluding microplastics (polyester microfibers) and food-contaminated plasticand upscaling the system from 2 to 120 mL while maintaining its efficiency for plastic conversion.

Water oxidation is the key kinetic bottleneck of photoelectrochemical devices for fuel synthesis. Despite advances in the identification of intermediates, elucidating the catalytic mechanism of this multi-redox reaction on metal-oxide photoanodes remains a significant experimental and theoretical challenge. Here we report an experimental analysis of water oxidation kinetics on four widely studied metal oxides, focusing particularly upon hematite. We observe that hematite is able to access a reaction mechanism third order in surface hole density, assigned to equilibration between three surface holes and M(OH)-O-M(OH) sites. This reaction exhibits a remarkably low activation energy (Ea ~ 60 meV). Density functional theory is employed to determine the energetics of charge accumulation and O-O bond formation on a model hematite 110 surface. The proposed mechanism shows parallels with the function of oxygen evolving complex of photosystem II, and provides new insights to the mechanism of heterogeneous water oxidation on a metal oxide surface.

Photocatalytic conversion of CO into carbonaceous feedstock chemicals is a promising strategy to mitigate greenhouse gas emissions and simultaneously store solar energy in chemical form. Photocatalysts for this transformation are typically based on precious metals and operate in nonaqueous solvents to suppress competing H generation. In this work, we demonstrate selective visible-light-driven CO reduction in water using a synthetic photocatalyst system that is entirely free of precious metals. We present a series of self-assembled nickel terpyridine complexes as electrocatalysts for the reduction of CO to CO in organic media. Immobilization on CdS quantum dots allows these catalysts to be active in purely aqueous solution and photocatalytically reduce CO with >90% selectivity under UV-filtered simulated solar light irradiation (AM 1.5G, 100 mW cm, λ > 400 nm, pH 6.7, 25 °C). Correlation between catalyst immobilization efficiency and product selectivity shows that anchoring the molecular catalyst on the semiconductor surface is key in controlling the selectivity for CO reduction over H evolution in aqueous solution.

The generation of renewable H2 through an efficient photochemical route requires photoinduced electron transfer (ET) from a light harvester to an efficient electrocatalyst in water. Here, we report on a molecular H2 evolution catalyst (NiP) with a DuBois-type [Ni(P2R′N2R″)2]2+ core (P2R′N2R″ = bis(1,5-R′-diphospha-3,7-R″-diazacyclooctane), which contains an outer coordination sphere with phosphonic acid groups. The latter functionality allows for good solubility in water and immobilization on metal oxide semiconductors. Electrochemical studies confirm that NiP is a highly active electrocatalyst in aqueous electrolyte solution (overpotential of approximately 200 mV at pH 4.5 with a Faradaic yield of 85 ± 4%). Photocatalytic experiments and investigations on the ET kinetics were carried out in combination with a phosphonated Ru(II) tris(bipyridine) dye (RuP) in homogeneous and heterogeneous environments. Time-resolved luminescence and transient absorption spectroscopy studies confirmed that directed ET from RuP to NiP occurs efficiently in all systems on the nano- to microsecond time scale, through three distinct routes: reductive quenching of RuP in solution or on the surface of ZrO2 (“on particle” system) or oxidative quenching of RuP when the compounds were immobilized on TiO2 (“through particle” system). Our studies show that NiP can be used in a purely aqueous solution and on a semiconductor surface with a high degree of versatility. A high TOF of 460 ± 60 h–1 with a TON of 723 ± 171 for photocatalytic H2 generation with a molecular Ni catalyst in water and a photon-to-H2 quantum yield of approximately 10% were achieved for the homogeneous system.

Artificial photosynthesis is the mimicry of the natural process of solar energy conversion into chemical energy carriers. Photocatalytic systems that combine light-harvesting materials and catalysts in solution or suspension provide a promising route towards this goal. A key requirement for a sustainable solar fuel production system is a low-cost, stable and non-toxic light harvester. Photoluminescent carbon nanoparticles, carbon dots (CDs), are promising emerging light-harvesters for photocatalytic fuel production systems. CDs possess many desirable properties for this purpose, such as inexpensive, scalable synthetic routes, low-toxicity and tuneable surface chemistry. In this tutorial review, the integration of CDs in photocatalytic fuel generation systems with metallic, molecular and enzymatic catalysts is discussed. An overview of CD types, synthesis and properties is given along with a discussion of tuneable CD properties that can be optimised for applications in photocatalysis. Current understanding of the photophysical electron transfer processes present in CD photocatalytic systems is outlined and various avenues for their further development are highlighted.