No abstract

Several factors can contribute to the achievement of success with endodontic therapy. After an effective microbial-control phase, an adequate canal and coronal filling will guarantee a high probability of success. Gutta-percha has for many years been widely used as a solid material in root fillings associated with different types of sealers. Even associated with a sealer, this material it is not capable of preventing leakage, as has been shown in many studies. In fact, because of gutta-percha's limitations, the seal of a coronal restoration may be as important as the gutta-percha fill in preventing reinfection of the root canal. Although sealers can form close adhesion to the root canal wall, none is able to bond to the gutta-percha core material. Upon setting, the sealer pulls away from the gutta-percha core, leaving a gap through which bacteria may pass. This article describes a new thermoplastic, synthetic root canal filling material, whose design is based on polyester chemistry, that looks and handles like gutta-percha. It is used in the same manner as most bonding systems. After the usual preparation of the root canal, a self-etch primer is used to condition the canal walls and prepare them for bonding to the resin. The resin sealant is introduced in the root canal. It bonds to the primer and to the resin core material; thus, a "monoblock" is formed without the gaps typical in gutta-percha fillings. Studies have shown that leakage of bacteria with this material is significantly reduced compared with gutta-percha.

The aim of this in vitro study was to evaluate the bond strength of Epiphany™ resin-based sealer to dentin walls after placement of calcium hydroxide [Ca(OH) 2 ] dressings. Fifteen extracted single-rooted human teeth were instrumented using 2.5% NaOCl + EDTA as irrigants. The teeth were randomly assigned to 3 groups (n=5), according to the intracanal dressing: G1= Ca(OH) 2 + saline; G2= Ca(OH) 2 + 2% chlorhexidine gluconate (CHX) gel; and G3= saline (control). After 10 days of storage in 100% humidity at 37°C, the dressings were removed and the root canals were filled with Epiphany™ sealer. After additional 48 h of storage, the specimens were sectioned transversally into 2-mm-thick discs. Push-out tests were performed (1 mm/min, Instron 4411) and the maximum loads at failure were recorded in MPa. One-way ANOVA and Newman-Keuls tests showed a statistically significant decrease in bond strength when a Ca(OH) 2 dressing was used before root canal filling with Epiphany™ (G1= 10.18 ± 1.99 and G2= 9.98 ± 2.97) compared to the control group (13.82 ± 3.9) (p< 0.05). It may be concluded that the use of Ca(OH) 2 as an intracanal dressing material affected the adhesion of Epiphany™ to the root canal walls, but even though the values were within the acceptable range found in the literature.

The effect of salivary exposure time on the abrasive wear of acid-eroded dentine was evaluated in situ. One-hundred and twenty bovine root dentine slabs were randomly assigned into six groups (A-F) and placed in intraoral palatal devices, which were worn by 10 volunteers for 4 d. On the first day, no erosive/abrasive procedures were carried out. On the following 3 d, erosive challenges were performed extraorally, two times per day, by immersing the device for 90 s in a soft drink. Subsequently, the group A specimens were immediately brushed (40 strokes), and the others were brushed after the following times: B, 20 min; C, 40 min; and D, 60 min. Group E specimens were only acid-eroded and those of group F were only brushed. Dentine wear was measured with a profilometer. anova and Dunnett's test showed that groups A-D did not differ statistically from the control group E but differed from the control group F. The lowest mean value was found for group F. Regression analysis was unable to show salivary effect on dentine wear reduction. The data suggest that the exposure time of saliva of up to 60 min has no effect on reducing the eroded dentine wear by toothbrushing.

No abstract

The wear resistance and roughness results of Filtek Supreme suggest that it is suitable for clinical use, mainly in areas that are more subject to abrasive wear, such as Class V restorations.

Fracture strength and fatigue parameters of three ceramic materials submitted to dynamic fatigue were evaluated. A machinable leucite-reinforced dental ceramic, aluminum oxide, and yttria-stabilized zirconia (YSZ) were tested. The inert strength of the materials was determined in air (25 degrees C) at stressing rates of 70, 250, 400 MPa/s for Porcelain, Alumina and YSZ respectively. The data was analyzed using a two-parameter Weibull distribution. The Weibull modulus (m) and the characteristic of fracture (sigma0) parameters were determined for each material. Specimens were also tested in 3-point bending at different stressing rates in distilled/deionized water at 37 degrees C (dynamic fatigue) in order to calculate the fatigue parameters n and ln B. The strength for each material was characterized using Strength-Probability-Time (SPT) diagrams for 1 day, 1 year and 10 years. YSZ showed a high-fracture strength sigma0 (1,459 MPa) at a failure probability of 63.2% and high resistance to subcritical crack growth. YSZ and alumina showed better resistance to slow crack growth than porcelain, indicating less susceptibility to strength degradation by stress corrosion. Lifetime predictions after 10 years indicate a reduction of 50%, 36% and 29% in strength for porcelain, alumina and YSZ respectively. YSZ seems to be a very promising material for long-term dental and biomedical applications.

No abstract