This paper investigates the physical and chemical ignition delay (ID) periods in the constant volume combustion cflamber of the Ignition Quality Tester (IQT). IQT was used to determine the derived cetane number (DCN) according to ASTM D6890-10a standards. The fuels tested were ultra low sulfur diesel (ULSD),, and two synthetic fuels ofSasol IPK and F-T SPK (S-8). A comparison was made between the DCN and cetane number (CN) determined according to ASTM-D613 standards. Tests were conducted under steady state conditions at a constant pressure of 21 bars and various air temperatures ranging from 778 K to 848 K. The rate of heat release (RHR) was calculated from the measured pressure trace, and a detailed analysis of the RHR trace was made particularly for the auto-ignition process. Tests were conducted to determine the physical and chemical delay periods by comparing results obtained from two tests. In the first test, the fuel was injected into air according to ASTM standards. In the second test, the fuel was injected into nitrogen. The point at which the two resultant pressure traces separated was considered to be the end of the physical delay period. The effects of the charge temperature on the total ID as defined in ASTM D6890-10a standards, as well as on the physical and chemical delays, were determined. It was noticed that the physical delay represented a significant part of the total ID over all the air temperatures covered in this investigation. Arrhenius plots were developed to determine the apparent activation energy for each fuel using dijferent IDs. The first was based on the total ID measured according to ASTM standards. The second was the chemical delay determined in this investigation. The activation energy calculated from the total ID showed higher values for lower CN fuels except Sasol IPK. The activation energy calculated from the chemical delay period showed consistency in the increase of the activation energy with the drop in CN including Sasol IPK. The difference between the two findings could be explained by examining the sensitivity of the physical delay period of different fuels to the change in air temperature.
Surrogates for JP-8 have been developed in the high temperature gas phase environment of gas turbines. In diesel engines, the fuel is introduced in the liquid phase where volatility plays a major role in the formation of the combustible mixture and autoignition reactions that occur at relatively lower temperatures. In this paper, the role of volatility on the combustion of JP-8 and five different surrogate fuels was investigated in the constant volume combustion chamber of the Ignition Quality Tester (IQT). IQT is used to determine the derived cetane number (DCN) according to ASTM D6890. The surrogate fuels were formulated such that their DCNs matched that of JP-8, but with different volatilities. Tests were conducted to investigate the effect of volatility on the autoignition and combustion characteristics of the surrogates using a detailed analysis of the rate of heat release immediately after the start of injection. In addition, the effect of volatility on the spray dynamics was investigated by Schlieren imaging in an optical accessible rapid compression machine (RCM), and the imaging data supported the conclusion made in the IQT tests. Furthermore, apparent activation energies of JP-8 and surrogate fuels were determined based on the chemical delay periods, which could be considered as a new parameter for developing surrogate fuel.
Concern about the depletion of petroleum reserves, rising prices of conventional fuels, security of supply and global warming have driven research toward the development of renewable fuels for use in diesel engines. These fuels have different physical and chemical properties that affect the diesel combustion process. This paper compares between the autoignition, combustion, performance and emissions of soy-bean derived biodiesel, Jet propellant (JP-8) and ultra low sulfur diesel (ULSD) in a high speed single-cylinder research diesel engine equipped with a common rail injection system. Tests were conducted at steady state conditions at different injection pressures ranging from 600 bar to 1200 bar. The ‘rate of heat release’ traces are analyzed to determine the effect of fuel properties on the ignition delay, premixed combustion fraction and mixing and diffusion controlled combustion fractions. Biodiesel produced the largest diffusion controlled combustion fraction at all injection pressures compared to ULSD and JP-8. At 600 bar injection pressure, the diffusion controlled combustion fraction for biodiesel was 53% whereas both JP-8 and ULSD produced 39%. In addition, the effect of fuel properties on engine performance, fuel economy, and engine-out emissions is determined. On an average JP-8 produced 3% higher thermal efficiency than ULSD. Special attention is given to the oxides of nitrogen (NOx) emissions and particulate matter characteristics. On an average biodiesel produced 37% less NOx emissions compared to ULSD and JP-8.
This paper investigates the effect of air inlet temperature on the auto-ignition of fuels that have different CN and volatility in a single cylinder diesel engine. The inlet air temperature is varied over a range of 30°C to 110°C. The fuels used are ultra-low-sulfur-diesel (ULSD), JP-8 (two blends with CN 44.1 & 31) and F-T SPK. Detailed analysis is made of the rate of heat release during the ignition delay period, to determine the effect of fuel volatility and CN on the auto-ignition process. A STAR-CD CFD model is applied to simulate the spray behavior and gain more insight into the processes that immediately follow the fuel injection including evaporation, start of exothermic reactions and the early stages of combustion. The mole fractions of different species are determined during the ignition delay period and their contribution in the auto-ignition process is examined. Arrhenius plots are developed to calculate the global activation energy for the auto-ignition reactions of these fuels. Correlations are developed for the ID and the mean air temperature and pressure.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.