No abstract

Crystallization is among the easiest ways to improve polymer barrier properties because of the tortuosity increase within the material and the strong coupling between amorphous and crystalline phases. In this work, poly(lactic acid) (PLA) films have undergone α' thermal crystallization or different drawing processes. Although no effect of α' thermal crystallization on water permeability is observed, the drawing processes lead to an enhancement of the PLA barrier properties. This work clearly shows that, in the case of PLA, the crystallinity degree is not the main parameter governing the barrier properties contrary to the crystalline and amorphous phase organizations which play a key role. X-ray analyses confirm that the macromolecular chain orientation in the amorphous phase is the main cause of the improvement of the drawn PLA water barrier property. This improvement is due to the orthotropic structure formation for sufficient draw ratios, particularly when using the Simultaneous Biaxial drawing mode. Moreover, independently of the draw conditions, the drawing process tends to reduce the plasticization coefficient. Consequently, the drawn material barrier properties are not much affected by the water passage.

No abstract

Advanced fibers revolutionized structural materials in the second half of the 20 th Century.However, all high-strength fibers developed to date are brittle. Recently, pioneering simultaneous ultrahigh strength and toughness were discovered in fine (<250 nm) individual electrospun polymer nanofibers (NFs). This highly desirable combination of properties was attributed to high macromolecular chain alignment coupled with low crystallinity. Quantitative analysis of the degree of preferred chain orientation will be crucial for control of NF mechanical properties. However, quantification of supramolecular nanoarchitecture in NFs with low crystallinity in the ultrafine diameter range is highly challenging. Here, we discuss applicability of traditional as well as emerging methods for quantification of polymer chain orientation in nanoscale one-dimensional samples. Advantages and limitations of different techniques are critically evaluated on experimental examples. It is shown that straightforward application of some of the techniques to subwavelength-diameter NFs can lead to severe quantitative and even qualitative artifacts. Sources of such size-related artifacts, stemming from instrumental, materials, and geometric phenomena at the nanoscale, are analyzed on the example of polarized Raman method, but are relevant to other spectroscopic techniques. A proposed modified, artifact-free method is demonstrated. Outstanding issues and their proposed solutions are discussed. The results provide guidance for accurate nanofiber characterization to improve fundamental understanding and accelerate development of nanofibers and related nanostructured materials produced by electrospinning or other methods. We expect that the discussion in this review will also be useful to studies of many biological systems that exhibit nanofilamentary architectures and combinations of high strength and toughness.

No abstract

Fragilityindex and cooperativity length characterizing the molecular mobility in the amorphous phase are for the first time calculated in drawn polylactide (PLA). The microstructure of the samples is investigated from wide-angle X-ray scattering (WAXS) whereas the amorphous phase dynamics are revealed from broadband dielectric spectroscopy (BDS) and temperature-modulated differential scanning calorimetry (TMDSC). The drawing processes induce the decrease of both cooperativity and fragility with the orientation of the macromolecules. Post-drawing annealing reveals an unusual absence of correlation between the evolutions of cooperativity length and fragility. The cooperativity length remains the same compared to the drawn sample while a huge increase of the fragility index is recorded. By splitting the fragility index in a volume contribution and an energetic contribution, it is revealed that the amorphous phase in annealed samples exhibits a high energetic parameter, even exceeding the amorphous matrix value. It is assumed that the relaxation process is driven in such a way that the volume hindrance caused by the thermomechanical constraint is compensated by the acceleration of segmental motions linked to the increase of degrees of freedom. This result should also contribute to the understanding of the constraint slackening in the amorphous phase during annealing of drawn PLA, which causes among others the decrease of its barrier properties.

Among all the emergent biobased polymers, poly­(ethylene 2,5-furandicarboxylate) (2,5-PEF) seems to be particularly interesting for packaging applications. This work is focused on the investigation of the relaxation dynamics and the macromolecular mobility in totally amorphous 2,5-PEF as well as in the less studied poly­(ethylene 2,4-furandicarboxylate) (2,4-PEF). Both biopolymers were investigated by differential scanning calorimetry and dielectric relaxation spectroscopy in a large range of temperatures and frequencies. The main parameters describing the relaxation dynamics and the molecular mobility in 2,5-PEF and 2,4-PEF, such as the glass transition temperature, the temperature dependence of the α and β relaxation times, the fragility index, and the apparent activation energy of the secondary relaxation, were determined and discussed. 2,5-PEF showed a higher value of the dielectric strength as compared to 2,4-PEF and other well-known polyesters, such as poly­(ethylene terephthalate), which was confirmed by molecular dynamics simulations. According to the Angell’s classification of glass-forming liquids, amorphous PEFs behave as stronger glass-formers in comparison with other polyesters, which may be correlated to the packing efficiency of the macromolecular chains and therefore to the free volume and the barrier properties.

Molecular mobility and physical ageing of amorphous plasticized polylactide (PLA) with two different contents of mesolactide are studied with the help of thermal analysis. Used plasticizers are acetyl tributyl citrate (ATBC) and triacetin (TA), two molecules with established miscibility and plasticizing efficiency. Lower plasticizer permanence of TA compared with ATBC is found. The plasticizer molecules decreased the size of the cooperativity domains at the glass transition temperature Tg and likely in the glassy state by decreasing intermacromolecular interactions and notwithstanding the mesolactide content of PLA and the chemical identity of the plasticizer. The recovery function is given and shows a significant effect of the plasticizer on the physical ageing. The supplementary free volume brought by the plasticizer enhances molecular mobility in the glassy state and increases structural relaxation at one order of magnitude. The comparison between different plasticizers reveals that the structural relaxation is however independent from the type of plasticizer and the percentage of mesolactide in PLA. POLYM. ENG. SCI., 55:858–865, 2015. © 2014 Society of Plastics Engineers