Context. Optical long-baseline interferometry is moving a crucial step forward with the advent of general-user scientific instruments that equip large aperture and hectometric baseline facilities, such as the Very Large Telescope Interferometer (VLTI). Aims. AMBER is one of the VLTI instruments that combines up to three beams with low, moderate and high spectral resolutions in order to provide milli-arcsecond spatial resolution for compact astrophysical sources in the near-infrared wavelength domain. Its main specifications are based on three key programs on young stellar objects, active galactic nuclei central regions, masses, and spectra of hot extra-solar planets. Methods. These key science goals led to scientific specifications, which were used to propose and then validate the instrument concept. AMBER uses single-mode fibers to filter the entrance signal and to reach highly accurate, multiaxial three-beam combination, yielding three baselines and a closure phase, three spectral dispersive elements, and specific self-calibration procedures. Results. The AMBER measurements yield spectrally dispersed calibrated visibilities, color-differential complex visibilities, and a closure phase allows astronomers to contemplate rudimentary imaging and highly accurate visibility and phase differential measurements. AMBER was installed in 2004 at the Paranal Observatory. We describe here the present implementation of the instrument in the configuration with which the astronomical community can access it. Conclusions. After two years of commissioning tests and preliminary observations, AMBER has produced its first refereed publications, allowing assessment of its scientific potential.

Aims. In this paper, we present an innovative data reduction method for single-mode interferometry. It has been specifically developed for the AMBER instrument, the three-beam combiner of the Very Large Telescope Interferometer, but it can be derived for any single-mode interferometer. Methods. The algorithm is based on a direct modelling of the fringes in the detector plane. As such, it requires a preliminary calibration of the instrument in order to obtain the calibration matrix that builds the linear relationship between the interferogram and the interferometric observable, which is the complex visibility. Once the calibration procedure has been performed, the signal processing appears to be a classical least-square determination of a linear inverse problem. From the estimated complex visibility, we derive the squared visibility, the closure phase, and the spectral differential phase. Results. The data reduction procedures have been gathered into the so-called amdlib software, now available for the community, and are presented in this paper. Furthermore, each step in this original algorithm is illustrated and discussed from various on-sky observations conducted with the VLTI, with a focus on the control of the data quality and the effective execution of the data reduction procedures. We point out the present limited performances of the instrument due to VLTI instrumental vibrations which are difficult to calibrate.

Abstract.A good astronomical site must fulfill several criteria including low atmospheric turbulence and low wind speeds. It is therefore important to have a detailed knowledge of the temperature and wind conditions of a location considered for future astronomical research. Antarctica has unique atmospheric conditions that have already been exploited at the South Pole station. Dome C, a site located on a local maximum of the Antarctic plateau, is likely to have even better conditions. In this paper we present the analysis of two decades of wind speed measurements taken at Dome C by an automated weather station (AWS). We also present temperature and wind speed profiles taken over four Antarctic summers using balloon-borne weather sondes. We will show that as well as having one of the lowest average wind speed ever recorded at an existing or potential observatory, Dome C also has an extremely stable upper atmosphere and a very low inversion layer.

During the austral winter 2005, the first astronomical site testing campaign were performed at Dome C, in Antarctica. Thirty-five meteorological balloons equipped with microthermal sensors were used to sense the vertical profile of the optical turbulence intensity C 2 N above Dome C up to 20 km. All the profiles of the 2005 campaign are statistically analyzed. We provide the median C 2N profiles and the mean potential temperature, mean horizontal wind speed, and mean direction profiles for the three seasons covered by this campaign (autumn, winter, and beginning of the spring). The structure of the optical turbulence in the atmosphere above Dome C is analyzed and compared with the well-known median C 2 N profiles of midlatitude sites. Of the whole optical turbulence, 80% lies within the first 33 m above the ground and 9% in the upper part of the boundary layer, between 33 m and 1 km above the ground. The remaining 11% are in the free atmosphere. This is an extreme situation when compared with "classical" midlatitude sites where the surface layer extends up to 200 m. This strong and thin surface layer is the result of the kinetic turbulent mixing of air combined with a strong potential temperature gradient. The site is characterized from the adaptive optics point of view. Seeing, isoplanatic angle, and coherence time are estimated for each considered seasons. A four-layer decomposition for each season is provided for adaptive optics simulations. For high angular astronomy, a telescope at Dome C needs to be elevated over this surface layer, or a specific GLAO needs to be designed. Combined with the unique possibility of performing continuous observation from Antarctica, scientific programs such as microlensing, pulsating stars, and asteroseismology become feasible.