Ventrikel Fibrilasi adalah irama yang umumnya didapat di permulaan henti jantung dan Ventrikel Takikardi yang disebabkan oleh gangguan listrik di jantung yang mengontrol gerakan pompa pada bilik atau ventrikel jantung, hal ini menyebabkan bilik berdenyut terlalu cepat dari biasanya. Ventrikel Fibrilasi dan Ventrikel Takikardi adalah sebagian dari penyebab kegagalan fungsi jantung, apabila tidak segera ditangani akan menyebabkan kematian. Salah satu cara menangani permasalahan ini yaitu dengan memberikan energi dengan bentuk kejut listrik dalam jumlah tertentu. Tujuan dari penelitian adalah untuk merancang sebuah modul defibrilator yang dapat menghasilkan energi dengan bentuk kejut listrik dan dilengkapi dengan mode sinkron dan asinkron. Kontribusi penelitian ini adalah sistem discharge dapat dilakukan secara defibrilasi dengan menekan tombol discharge atau disebut juga dengan mode asinkron dan sistem discharge dapat dilakukan secara kardioversi dengan menekan tombol discharge serta melakukan penyadapan BPM yang telah tersedia pada alat atau disebut juga dengan mode sinkron. Penelitian ini menggunakan modul ekg AD8232 untuk melakukan penyedapan sinyal ekg sehingga dapat menghasilkan nilai BPM. Komponen yang digunakan seperti Arduino Atmega untuk melakukan pemprosesan alat, Kapasitor dengan Kapsitansi tertentu untuk melakukan penyimpanan energi sementara, dan TFT NEXTION 2.8” sebagai tampilan dan tempat setting alat. Untuk penelitian lebih lanjut dapat menambahkan tampilan sinyal ekg, menambah besaran energi, dan menggunakan baterai untuk membuat perangkat portabel.
Sinyal monofasik memiliki satu arus puncak tinggi yang dapat menyebabkan kerusakan pada jantung. Tujuan dari penelitian ini yaitu untuk mendesain suatu defibrillator yang dapat meminimalisir resiko atau dampak akibat penggunaan sinyal monofasik. Kontribusi peneitian ini adalah sistem dapat menghasilkan sinyal bifasik yang membutuhkan tegangan lebih rendah dan energi lebih rendah daripada sinyal monofasik, untuk dapat menghasilkan tegangan dan energi yang lebih rendah maka dibutuhkan dua kondensator sehingga pengisian dapat disesuaikan dengan rumus perhitungan energi. Penelitian ini menggunakan dua mosfet dan dua kondensator dengan spesifikasi 1000 uF 400 V, proses menghasilkan sinyal bifasik dilakukan dengan pengisian dua kondensator, jika nilai tegangan pada kondensator telah tercapai maka pengisian akan berhenti sesuai setting nilai tegangan pada pembagian tegangan selanjutnya mosfet akan mengatur pembuangan muatan pada kondensator secara bergantian dan membalik paddle. Penggunaan sinyal bifasik ditentukan yaitu kondensator I memuat tegangan sebesar 2/3 nilai setting dan kondensator II memuat tegangan sebesar 1/3 nilai setting. Hasil dari pengukuran pada sinyal bifasik menunjukkan adanya perbedaan muatan kondensator dengan desain penelitian, nilai rata – rata error pada kondensator I didapatkan sebesar 0,36 % dan 0,74 % pada kondensator II.Hasil penelitian ini dapat di jadikan referensi untuk penelitian selanjutnya dengan memperbaiki atau meminimalisir nilai error pada penggunaan kedua sinyal dan meningkatkan nilai energi pada alat. Monophasic signals have a high peak current which can cause damage to the heart. The purpose of this study is to design a defibrillator that can minimize the risk or impact due to the use of monophasic signals. The contribution of this research is that the system can produce biphasic signals which require lower voltage and lower energy than monophasic signals, to be able to produce lower voltage and energy, two condensers are needed so that charging can be adjusted to the energy calculation formula. This study uses two mosfets and two condensers with specifications of 1000 uF 400 V, the process of producing biphasic signals is done by charging two condensers, if the voltage value on the condenser has been reached, the charging will stop according to the voltage value setting at the next voltage division. the condenser alternately and flips the paddle. The use of biphasic signals is determined, ie condenser I contains a voltage of 2/3 the setting value and condenser II contains a voltage of 1/3 the setting value. The results of measurements on the biphasic signal showed that there were differences in the load of the condenser with the research design, the average error value in the condenser I was 0.36% and 0.74% in the condenser II. The results of this study can be used as a reference for further research by improving or minimizing the error value in the use of both signals and increasing the energy value of the device.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.