No abstract

No abstract

/npsi/ctrl?action=rtdoc&an=3539033&lang=en http://nparc.cisti-icist.nrc-cnrc.gc.ca/npsi/ctrl?action=rtdoc&an=3539033&lang=frAccess and use of this website and the material on it are subject to the Terms and Conditions set forth at http://nparc.cisti-icist.nrc-cnrc.gc.ca/npsi/jsp/nparc_cp.jsp?lang=en NRC Publications Archive Archives des publications du CNRCThis publication could be one of several versions: author's original, accepted manuscript or the publisher's version. / La version de cette publication peut être l'une des suivantes : la version prépublication de l'auteur, la version acceptée du manuscrit ou la version de l'éditeur. For the publisher's version, please access the DOI link below./ Pour consulter la version de l'éditeur, utilisez le lien DOI ci-dessous.http://dx.doi.org/10.1039/b700322fLab on Chip, 7, 2007-01-01 Microarrays have become one of the most convenient tools for high throughput screening, supporting major advances in genomics and proteomics. Other important applications can be found in medical diagnostics, detection of biothreats, drug discovery, etc. Integration of microarrays with microfluidic devices can be highly advantageous in terms of portability, shorter analysis time and lower consumption of expensive biological analytes. Since fabrication of microfluidic devices using traditional materials such as glass is rather expensive, there is great interest in employing polymeric materials as a low cost alternative that is suitable for mass production. A number of commercially available plastic materials were reviewed for this purpose and poly(methylmethacrylate) Zeonor 1060R and Zeonex E48R were identified as promising candidates, for which methods for surface modification and covalent immobilization of DNA oligonucleotides were developed. In addition, we present proof-of-concept plastic-based microarrays with and without integration with microfluidics.

No abstract

Today, the focus in microfluidic platforms for diagnostics is on the integration of several analysis steps toward sample-to-answer systems. One of the main challenges to integration is the requirement for serial valving to allow the sequential release of fluids in a temporally and spatially controlled manner. The advantages offered by centrifugal microfluidic platforms make them excellent candidates for integration of biological analysis steps, yet they are limited by the lack of robust serial valving technologies. This is especially true for the majority of centrifugal microfluidic devices that rely on hydrophilic surfaces, where few passive serial valving techniques function reliably. Building on the useful functionality of centrifugal microfluidic siphoning previously shown, a novel serial siphon valve is introduced that relies on multiple, inline siphons to provide for a better controlled, sequential release of fluids. The introduction of this novel concept is followed by an analytical analysis of the device.Proof-of-concept is also demonstrated, and examples are provided to illustrate the range of functionality of the serial siphon valve. The serial siphon is shown to be robust and reproducible, with variability caused by the dependence on contact angle, rotation velocity, and fluidic properties (viz., surface tension) significantly reduced compared to current microfluidic, centrifugal serial valving technologies.

The organization of cells and extracellular matrix (ECM) in native tissues plays a crucial role in their functionality. However, in tissue engineering, cells and ECM are randomly distributed within a scaffold. Thus, the production of engineered-tissue with complex 3D organization remains a challenge. In the present study, we used contact guidance to control the interactions between the material topography, the cells and the ECM for three different tissues, namely vascular media, corneal stroma and dermal tissue. Using a specific surface topography on an elastomeric material, we observed the orientation of a first cell layer along the patterns in the material. Orientation of the first cell layer translates into a physical cue that induces the second cell layer to follow a physiologically consistent orientation mimicking the structure of the native tissue. Furthermore, secreted ECM followed cell orientation in every layer, resulting in an oriented self-assembled tissue sheet. These self-assembled tissue sheets were then used to create 3 different structured engineered-tissue: cornea, vascular media and dermis. We showed that functionality of such structured engineered-tissue was increased when compared to the same qnon-structured tissue. Dermal tissues were used as a negative control in response to surface topography since native dermal fibroblasts are not preferentially oriented in vivo. Non-structured surfaces were also used to produce randomly oriented tissue sheets to evaluate the impact of tissue orientation on functional output. This novel approach for the production of more complex 3D tissues would be useful for clinical purposes and for in vitro physiological tissue model to better understand long standing questions in biology.

No abstract

Multilayer soft lithography of polydimethylsiloxane (PDMS) is a well-known method for the fabrication of complex fluidic functions. With advantages and drawbacks, this technique allows fabrication of valves, pumps and micro-mixers. However, the process is inadequate for industrial applications. Here, we report a rapid prototyping technique for the fabrication of multilayer microfluidic devices, using a different and promising class of polymers. Using styrenic thermoplastic elastomers (TPE), we demonstrate a rapid technique for the fabrication and assembly of pneumatically driven valves in a multilayer microfluidic device made completely from thermoplastics. This material solution is transparent, biocompatible and as flexible as PDMS, and has high throughput thermoforming processing characteristics. We established a proof of principle for valving and mixing with three different grades of TPE using an SU-8 master mold. Specific viscoelastic properties of each grade allow us to report enhanced bonding capabilities from room temperature bonding to free pressure thermally assisted bonding. In terms of microfabrication, beyond classically embossing means, we demonstrate a high-throughput thermoforming method, where TPE molding experiments have been carried out without applied pressure and vacuum assistance within an overall cycle time of 180 s. The quality of the obtained thermoplastic systems show robust behavior and an opening/closing frequency of 5 Hz.