The fatigue life of offshore wind turbine (OWT) support structures is sensitive to variations in site-specific conditions such as the water depth and soil properties. Site condtions may vary significantly within a wind farm, and they may change throughout the lifetime of the OWT. This paper analyses how control strategies for fatigue life extension can compensate for differing fatigue loads due to varying site conditions. Control strategies applicable for both power production and idling situations are analysed, and methodology to reduce undesirable side-effects is proposed. The design case is a 10MW monopile OWT located in 30 meter water depth at the Dogger Bank in the North Sea, and results are based on time-domain simulations performed using an aero-hydro-servo-elastic simulation tool. The results show that, when all the investigated control strategies are utilized, a fatigue damage reduction over the 20-year lifetime of approximately 50% is possible. Furthermore, it is shown that adverse side-effects such as wear of pitch actuators and fluctuations in the power output can be significantly reduced by limiting the use of control strategies to some predefined situations. With only moderate cost to other system components, the control system is able to compensate for 20% variation in soil stiffness, and 5% (1.5 meter) variation in water depth.

A simulation study is performed to identify the key contributors to lifetime accumulated fatigue damage in the support-structure of a 10 MW offshore wind turbine placed on a monopile foundation in 30 m water depth. The relative contributions to fatigue damage from wind loads, wave loads, and wind/wave misalignment are investigated through time-domain analysis combined with long-term variations in environmental conditions. Results show that wave loads are the dominating cause of fatigue damage in the support structure, and that environmental condtions associated with misalignment angle > 45° are insignificant with regard to the lifetime accumulated fatigue damage. Further, the results are used to investigate the potential of event-based use of control strategies developed to reduce fatigue loads through active load mitigation. Investigations show that a large reduction in lifetime accumulated fatigue damage is possible, enabling load mitigation only in certain situations, thus limiting collateral effects such as increased power fluctuations, and wear and tear of pitch actuators and drive-train components.

The dimensions of offshore wind turbine (OWT) support structures are governed by fatigue considerations. For 6‐ to 10‐MW OWTs, wave loads are often dominating in terms of fatigue utilization. The present work proposes a control scheme to reduce the wave‐induced fatigue loads in OWT support structures. The control scheme applies collective pitch control to increase both the damping and stiffness of the fore‐aft vibration modes. With conventional active tower damping, efficient wave disturbance rejection is restricted to a narrow frequency range around the first fore‐aft modal frequency. The proposed control scheme achieves efficient wave disturbance rejection across a broader frequency range. Here, tower feedback control is implemented via an auxiliary control loop. Based on a low‐fidelity model, the effect of the tower feedback loop on the stability margins of the basic controller is analysed. The results show that, within certain boundaries, the stability margins are improved by the stiffness term in the tower feedback loop. Consequently, the need to reduce the bandwidth of the basic controller to accommodate tower feedback control is relaxed. Based on time‐domain simulations carried out in an aero‐hydro‐servo‐elastic simulation tool, the lifetime effects of the proposed control scheme are analysed. Compared with conventional active tower damping, a more favourable trade‐off between adverse side effects and the support structure's fatigue damage is achieved with the proposed control scheme.

The cost of offshore wind energy can be reduced by incorporating control strategies to reduce the support structures' load effects into the structural design process. While effective in reducing the cost of support structures, load‐reducing controls produce potentially costly side effects in other wind turbine components and subsystems. This paper proposes a methodology to mitigate these side effects at the wind farm level. The interaction between the foundation and the surrounding soil is a major source of uncertainty in estimating the safety margins of support structures. The safety margins are generally closely correlated with the modal properties (natural frequencies, damping ratios). This admits the possibility of using modal identification techniques to reassess the structural safety after installing and commissioning the wind farm. Since design standards require conservative design margins, the post‐installation safety assessment is likely to reveal better than expected structural safety performance. Thus, if load‐reducing controls have been adopted in the structural design process, it is likely permissible to reduce the use of these during actual operation. Here, the probabilistic outcome of such a two‐stage controls adaptation is analyzed. The analysis considers the structural design of a 10 MW monopile offshore wind turbine under uncertainty in the site‐specific soil conditions. Two control strategies are considered in separate analyses: (a) tower feedback control to increase the support structure's fatigue life and (b) peak shaving to increase the support structure's serviceability capacity. The results show that a post‐installation adaptation can reduce the farm‐level side‐effects of load‐reducing controls by up to an order of magnitude.