Geopolymers are exclusively mineral nature and are considered an alternative to materials based on Portland clinker, whose production accounts for about 5% of anthropogenic CO 2 emissions in the world. The geopolymer cement concrete (GCC) may be prepared from natural oxide-aluminosilicates such as metakaolin (MK), or synthetic, such as fly ash (FA) together with active silica contained in the rice husk ash (RHA). The fracture properties of the Portland cement concrete (PCC) with 25 MPa and 50 MPa, and of three different geopolymeric concretes with the same strength Classes were determined for comparative analysis. The aim of this study is to provide support to begin the use of geopolymers in the reinforced concrete precasting Industry. Three-point bending tests of notched beams with a/d (notch depth/beam depth) of 0.5 from RILEM TC80-FMT Recommendations were used to determine the critical values of K, G, R and J-integral for crack propagation under mode I. The results showed that the geopolymeric concretes exhibit similar mechanical behavior and fracture properties higher that those determined in PCC for the same strength class.
Geopolymeric materials have some unique properties such as early-high compressive strength, durability, resistance to acids and sulfates, ability to immobilize toxic and radioactive compounds, low porosity and high temperature resistance. These materials are strategic for sustainable development and are a suitable alternative to Portland cement. The use of phyllite as a geopolymer precursor is encouraged by its abundance, low cost, and the fact that it is already applied in ceramic industries as a kaolin substitute. The objective of this paper is the physicochemical characterization of geopolymeric resin using two pulverized phyllite rocks as precursors with STEM, XRD and XRF techniques. It was found that both phyllite rocks studied have a high quartz content of approximately 50% (weight), which have a "filler" function in the microstructure of the resin helping stabilize residual tensions after curing. Kaolinite and muscovite minerals are present in up to 40% (weight) and are responsible for the high compressive strength of the geopolymer resins.
RESUMOEsse trabalho apresenta um estudo comparativo do comportamento mecânico de vigas pré-moldadas de concreto armado convencional (CCP), fabricadas por uma empresa local e de concretos geopolimérico de metacaulim (CCG) e geopolimérico com 20% de cinza volante e silicato de cinza de casca de arroz (CCG-20CV-CCA), como matrizes substitucionais. Os resultados mostraram que os concretos geopoliméricos apresentaram comportamento similar ao do CCP, na mesma classe de resistência do concreto, taxa de armadura e disposição das armaduras no elemento estrutural estudado. O uso das cinzas promoveu aumento do módulo de rigidez à flexão e dos limites de deformação das vigas geopoliméricas, em especial para a CCG-20CV-CCA sob a maior taxa de armadura. Os padrões de fissuração e os modos de ruptura encontrados foram similares àqueles mostrados pelo CCP, com a conclusão, neste estudo de caso, de que as vigas pré-moldadas, como fabricadas pela empresa, foram superarmadas ao longo do bordo superior. Embora o dimensionamento da viga não tenha sido objeto deste estudo, foi mostrado que o concreto geopolimérico pode substituir plenamente o CCP, em concreto armado, abrindo oportunidade de uso dos mesmos códigos de dimensionamento desenvolvidos para este material tradicional. Palavras-chave:Geopolímero. Pré-moldado. Concreto armado. ABSTRACTThis work presents a comparative study of the mechanical behavior of precast concrete beams (CCP), manufactured by a local company and geopolymer concrete of metakaolin (CCG) and geopolymer concrete with 20% of fly ash and rice husk ash silicate (CCG-20CV-CCA), as substitutional matrices. The results showed that the geopolymer concretes presented similar behavior to the CCP, in the same class of concrete strength, reinforcement rate and arrangement in the structural element studied. The use of the ashes promoted an increase of the flexural stiffness modulus and the limits of deformation of the geopolymer beams, in particular for the CCG-20CV-CCA under the highest reinforcement rate. The cracking patterns and failure modes found were similar to those shown by CCP, with the conclusion, in this case study, that precast beams, as manufactured by the company were super-reinforced along the top of the beams. Although the dimensioning of the beam has not been the object of this study, it has been shown that the geopolymer concrete can completely replace the CCP in reinforced concrete, opening up the opportunity to use the same structural design codes developed for this traditional material.
O presente trabalho é um estudo preliminar das potencialidades de emprego de metacaulins obtidos a partir da calcinação controlada de rejeitos de beneficiamento de caulins comerciais, na produção de geopolímeros para aplicações estruturais. Os resultados de caracterização mostraram composições químicas similares, mas diferenças significativas de granulometria entre os seis tipos de rejeito estudados. Análises por microscopia eletrônica de varredura (MEV) e difração de raios X (DRX) foram realizadas para investigar a morfologia das partículas, confirmar as composições química e mineralógica e verificar se a calcinação foi capaz de amorfizar a estrutura da caulinita. As amostras calcinadas foram comparadas entre si e com uma amostra de referência e usadas como precursor aluminossilicato em uma formulação padrão, tendo sua consistência em estado fresco e a resistência à compressão no estado endurecido determinadas. Os resultados destacaram apenas duas amostras calcinadas consideradas em conformidade com o padrão, embora se considere que o beneficiamento por moagem e a calcinação por tempo mais longo conduza à resultados mais promissores.
A oportunidade gerada pela álcali-ativação de escórias granuladas de alto forno abriu perspectiva para ex-ploração desta tecnologia no tocante a outros materiais baseados no sistema SiO2-Al2O3-CaO. Apesar disso, poucos estudos evidenciam os efeitos da álcali-ativação nos cimentos Portland que contém adições de escó-ria ou de pozolana, e que elucidem o que ocorre, em termos de microestrutura e propriedades, se diferentes tipos e teores de álcalis forem utilizados. Este artigo apresenta um trabalho de investigação dos efeitos da álcali-ativação nos tempos de pega e na resistência à compressão de um tipo comercial de cimento Portland composto com escória de alto forno, e na microestrutura desenvolvida. Os resultados revelaram que a pega e o endurecimento podem ser acelerados até o ponto de serem instantâneos, e que resistências à compressão da ordem de 70% da resistência máxima prevista pelo fabricante, aos 28 dias de idade, podem ser alcança-das em menos de 24 horas. Contudo, as análises microestruturais por MEV, DRX e DSC, indicaram que a incorporação dos álcalis interfere significativamente na cinética das reações de hidratação, principalmente na formação do hidróxido de cálcio e das fases AFm e AFt, levando-as à alterações morfológicas e compo-sicionais anômalas, que podem ser instáveis e gerar o comprometimento da resistência mecânica, em idades mais tarde.
O conteúdo dos livros e seus dados em sua forma, correção e confiabilidade são de responsabilidade exclusiva dos autores. Permitido o download da obra e o compartilhamento desde que sejam atribuídos créditos aos autores, mas sem a possibilidade de alterá-la de nenhuma forma ou utilizá-la para fins comerciais.
The addition of certain pozzolanic materials to Portland cement significantly changes the properties of the hardened matrix. If it has too high content of blast furnace slag, as the case of blast furnace Portland cements (BFPC), the early and late compressive strengths can be severely delayed or reduced. The objective this work was to investigate the potential of alkali-activation of BFPC and metakaolin (MK) blends by different types and contents of alkali-activators. The results clearly showed the influence of the MK pozzolanic activity and the type and content of activator used, in the development of compressive strengths of BFPC-MK blends. Microstructural analysis by SEM/EDS, DSC and XRD shown that the consumption of portlandite and the extra formation of C-S-(A)-H phases are the main positive effects registered. However, MK also promotes the formation of ettringite and unstable hydrated calcium aluminate phases, which, with the course of hydration, undergo a change in structure and volume loss, contributing to the reduction of final strengths. Content of 25% MK and 7.5% Na2SiO3 provided the best mechanical strength. The microstructures formed showed greater formation of ettringite, however there was also a reduction in portlandite and massive formation of C-S-H and C-S-(A)-H products.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.