Molecularly Imprinted Polymers (MIPs) are generic alternatives to antibodies in sensors, diagnostics and separations. To displace biomolecules without radical changes in infrastructure in device manufacture, MIPs should share their characteristics (solubility, size, specificity and affinity, localized binding domain) whilst maintaining the advantages of MIPs (low-cost, short development time and high stability) hence the interest in MIP nanoparticles. Herein we report a reusable solid-phase template approach (fully compatible with automation) for the synthesis of MIP nanoparticles and their precise manufacture using a prototype automated UV photochemical reactor. Batches of nanoparticles (30-400 nm) with narrow size distributions imprinted with: melamine (d = 60 nm, = 6.3 × 10 m), vancomycin (d = 250 nm, = 3.4 × 10 m), a peptide (d = 350 nm, = 4.8 × 10 m) and proteins have been produced. Our instrument uses a column packed with glass beads, bearing the template. Process parameters are under computer control, requiring minimal manual intervention. For the first time we demonstrate the reliable re-use of molecular templates in the synthesis of MIPs (≥ 30 batches of nanoMIPs without loss of performance). NanoMIPs are produced template-free and the solid-phase acts both as template and affinity separation medium.

A technique for coating microplate wells with molecularly imprinted polymers (MIPs) specific for proteins is presented. 3-Aminophenylboronic acid was polymerized in the presence of the following templates: microperoxidase, horseradish peroxidase, lactoperoxidase, and hemoglobin, via oxidation of the monomer by ammonium persulfate. This process resulted in the grafting of a thin polymer layer to the polystyrene surface of the microplates. Imprinting resulted in an increased affinity of the polymer toward the corresponding templates. The influence of the washing procedure, template concentration, and buffer pH on the polymer affinity was analyzed. It was shown that the stabilizing function of the support and spatial orientation of the polymer chains and template functional groups are the major factors affecting the imprint formation and template recognition. Easy preparation of the MIPs, their high stability, and their ability to recognize small and large proteins, as well as to discriminate molecules with small variations in charge, make this approach attractive and broadly applicable in biotechnology, assays and sensors.

One of the difficulties with using molecularly imprinted polymers (MIPs) and other electrically insulating materials as the recognition element in electrochemical sensors is the lack of a direct path for the conduction of electrons from the active sites to the electrode. We have sought to address this problem through the preparation and characterization of novel hybrid materials combining a catalytic MIP, capable of oxidizing the template, catechol, with an electrically conducting polymer. In this way a network of "molecular wires" assists in the conduction of electrons from the active sites within the MIP to the electrode surface. This was made possible by the design of a new monomer that combines orthogonal polymerizable functionality; comprising an aniline group and a methacrylamide. Conducting films were prepared on the surface of electrodes (Au on glass) by electropolymerization of the aniline moiety. A layer of MIP was photochemically grafted over the polyaniline, via N,N'-diethyldithiocarbamic acid benzyl ester (iniferter) activation of the methacrylamide groups. Detection of catechol by the hybrid-MIP sensor was found to be specific, and catechol oxidation was detected by cyclic voltammetry at the optimized operating conditions: potential range -0.6 V to +0.8 V (vs Ag/AgCl), scan rate 50 mV/s, PBS pH 7.4. The calibration curve for catechol was found to be linear to 144 microM, with a limit of detection of 228 nM. Catechol and dopamine were detected by the sensor, whereas analogues and potentially interfering compounds, including phenol, resorcinol, hydroquinone, serotonin, and ascorbic acid, had minimal effect (< or = 3%) on the detection of either analyte. Non-imprinted hybrid electrodes and bare gold electrodes failed to give any response to catechol at concentrations below 0.5 mM. Finally, the catalytic properties of the sensor were characterized by chronoamperometry and were found to be consistent with Michaelis-Menten kinetics.

A simple and straightforward technique for coating microplate wells with molecularly imprinted polymer nanoparticles (nanoMIPs) to develop assays similar to the enzyme-linked immunosorbent assay (ELISA) is presented here for the first time. NanoMIPs were synthesized by a solid-phase approach with an immobilized vancomycin (template) and characterized using Biacore 3000, dynamic light scattering, and electron microscopy. Immobilization, blocking, and washing conditions were optimized in microplate format. The detection of vancomycin was achieved in competitive binding experiments with a horseradish peroxidase-vancomycin conjugate. The assay was capable of measuring vancomycin in buffer and in blood plasma within the range of 0.001-70 nM with a detection limit of 0.0025 nM (2.5 pM). The sensitivity of the assay was 3 orders of magnitude better than a previously described ELISA based on antibodies. In these experiments, nanoMIPs have shown high affinity and minimal interference from blood plasma components. Immobilized nanoMIPs were stored for 1 month at room temperature without any detrimental effects to their binding properties. The high affinity of nanoMIPs and the lack of a requirement for cold chain logistics make them an attractive alternative to traditional antibodies used in ELISA.

In the presence of a template, desmetryn, commercial porous polypropylene membranes were photografted, using benzophenone as photoinitiator, with the functional monomer 2-acrylamido-2-methylpropanesulfonic acid and the cross-linker N,N′-methylenebis(acrylamide) in water. The influence of the polymerization conditions on membrane properties was studied by solute sorption analyses and membrane permeability measurements as well as electron spectroscopy for chemical analysis, FTIR spectroscopy, BET analysis, and scanning electron microscopy. It was found that molecularly imprinted polymer (MIP) membranes can be obtained which possess group affinity for the template and other triazine herbicides. Remarkably, the MIP membrane affinity for the template in buffer solution can be improved by the presence of salt during photograft copolymerization. This work presents the first successful example for molecular imprinting by in situ polymerization in water and on the surface of a commercially available synthetic polymer. The novel MIP membranes can be used in a fast preconcentration step, solid-phase extraction, by a simple microfiltration for the determination of herbicides in water. The possibility to introduce specific binding sites into porous membranes by surface imprinting polymerization without reducing their high permeabilities opens a general way to design new high-performance affinity membranes.

No abstract

No abstract

A new technique for coating microtitre plates with molecularly imprinted polymers (MIP), specific for low-molecular weight analytes (epinephrine, atrazine) and proteins is presented. Oxidative polymerization was performed in the presence of template; monomers: 3-aminophenylboronic acid (APBA), 3-thiopheneboronic acid (TBA) and aniline were polymerized in water and the polymers were grafted onto the polystyrene surface of the microplates. It was found that this process results in the creation of synthetic materials with antibody-like binding properties. It was shown that the MIP-coated microplates are particularly useful for assay development. The high stability of the polymers and good reproducibility of the measurements make MIP coating an attractive alternative to conventional antibodies or receptors used in enzyme linked immunosorbent assay (ELISA).