This paper focuses on the removal of methylene blue by adsorption using a mixture of titaniferous sand and attapulgite. The different adsorbents were characterized by X-ray fluorescence spectroscopy and their different parameters such as pH, zero charge potential, and specific surface area were determined. The experiments performed were optimized and modeled by a full 2-level and 4-factor design. The four factors are the ratio of titaniferous sand and attapulgite, the concentration of methylene blue, pH, and time. These vary from 4 to 19, 20 to 100 mg/L, 2 to 9, and 30 to 150 min respectively. The study of the effects of the different factors showed that the effect of methylene blue concentration and pH significantly influence the adsorption capacity and removal efficiency of the dye. The optimum parameters (adsorbent ratio, adsorbate concentration, pH and time) obtained for the adsorption capacity through the desirability function are: 19, 100mg/L, 9 and 150min. Those obtained for the yield are: 4, 100mg/L, 9, 150min. The pseudo second order adsorption kinetics gave an equilibrium adsorption capacity qe (calculated) = 7.6863 mg/g which is almost equal to that obtained experimentally qe (exp) = 7.3562 mg/g. This shows that the pseudo second order kinetic model is the adequate mathematical model to describe the methylene blue adsorption phenomenon on the mixture of titaniferous sand and attapulgite. The thermodynamic study showed that the methylene blue adsorption reaction is exothermic, non-spontaneous, and the degree of disorder of the particles at the adsorbing surface decreases.
Ce travail est une comparaison des capacités d’électro-oxydation du cristal violet sur des électrodes de Ti/TiO2 et Ti/IrO2-RuO2. Les résultats révèlent que le dépôt d’oxyde de métaux semi-conducteurs sur un support métallique adéquat tel que le titane permet d’améliorer l’activité électrochimique de ces électrodes. De même que l’influence des paramètres opératoires que sont la densité de courant (4,4, à 6,6 mA∙cm-2), la concentration de l’électrolyte (0,5 à 1,5 g∙L-1), la concentration initiale du colorant (2,5 x 10-5 à 10-4 M) et la surface d’électrode (4,55, 5,85 et 7,15 cm2) sur l’efficacité du traitement serait liée à la nature de l’électrode. Le suivi de la demande chimique en oxygène (DCO) au cours de l’électrolyse montre que Ti/IrO2-RuO2 possède le meilleur rendement épuratoire, puisqu’il permet d’atteindre un taux de réduction de la DCO de 92 % comparativement à un taux de 83 % enregistré dans le cas de Ti/TiO2 au bout de 2 h de traitement.
This study investigates the potential of using the mixture of titaniferous sand and attapulgite as adsorbents in a fixed bed adsorption process to remove a synthetic dye such as methylene blue in aqueous media. The different adsorbents were characterised by X-ray fluorescence spectroscopy and infrared spectroscopy. The different physico-chemical parameters such as pH, zero charge potential, bulk and absolute density, porosity and specific surface area were determined. The sizing algorithm used resulted in a number of transfer units (NUT) equal to 20.109, a height of transfer unit (HUT) equal to 0.515, a material transfer coefficient (Kya) equal to 3.159 and a height of the column (Z) equal to 1.05m. The influence of different experimental parameters such as initial dye concentration, adsorbent bed height and feed rate on the breakthrough curve was investigated. Various simple mathematical models such as Adams-Bohart and Thomas were applied in order to study the dynamic behaviour of the column and to estimate some kinetic coefficients through the experimental data obtained from the dynamic studies performed on the fixed bed. The results showed that the Thomas and Adams-Bohart models perfectly describe the behaviour of the breakthrough curves with values of coefficients of determination R2 that are higher than 0.90 except for the concentration of the dye equal to 50mg/L which has a coefficient R2 equal to 0.88.
This present study comes in addition to overcome the problems of separation of fine particles of TiO 2 in heterogeneous photocatalysis after treatment. It aims to show the potential for using titaniferous sand as a new semiconductor under solar irradiation. The photocatalytic efficiency of this titaniferous sand was tested on a pesticide (Azadirachtin). A tubular photocatalytic reactor with recirculation of the polluting solution was designed for the elimination of the pesticide in an aqueous solution. Before its use as a photocatalyst, the titaniferous sand has undergone a specific treatment that consists of calcination at 600˚C followed by extraction of the calcined natural organic materials, which can interfere with the measurement of analytical parameters such as COD. The titaniferous sand was also characterized by X-ray fluorescence spectroscopy (XRF). XRF analyses have shown that TiO 2 is predominant in the titaniferous sand with a percentage that has been estimated at 46.34%. The influence of various experimental parameters such as the flow rate of the polluting solution, the concentration of titaniferous sand, the presence of oxygen and the intensity of the overall rate of sunshine, was studied to optimize the photocatalytic degradation of the pesticide. The results showed that the highest removal rate (70%) was observed under the following conditions: a pH of 6, a titaniferous sand concentration of 150 g/L, a flow rate of 0.3 mL/min, and a sunshine rate of 354 W/m 2 and in the presence of atmospheric oxygen. Under these experimental conditions, the rate of photodegradation of the pesticide follows the pseudo first order kinetic model of Langmuir Hinshelwood with a coefficient of determination R 2 of 0.9869 and an apparent rate constant of 0.0029 min −1 . The results clearly demonstrated the potential of titaniferous
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.