Electronic scales are heavy gauges that are widely used both in the laboratory and in the business world. One of the main sensors of electronic scales is the load cell. The direct use of load cell will result in the achievement of the standard resolution of the load cell or ADC system used, so the resolution of the scales will be quite low as it is determined only by the load cell measurement range and the ADC resolution where the dynamic range of the ADC is not reached.In this article will be made electronic efforts to increase the resolution of the scales so that the accuracy of weighing can be better. Improved resolution attempts are made with electronic signal processor and conditioners, among others, by amplifying, summing and leveling amplifiers and to prevent noise being attempted by filtering. Data processing is done by comparing the resolution value of Load cell without signal conditioner and load cell resolution with signal conditioner. Load Cell with a load range of 0 - 5 kg in conditioning with 200x gain obtained output 113 mV to 1200 mV. With a standard ADC at a resolution of 20 mV / bit will be obtained 0000 0110 to 0011 1110 By adding a Leveling Amplifier circuit obtained output 48 mV for load 0 kg and 4.87 Volt for 5 kg load, ADC output in the range 0000 0010 to 1111 1100. Usage ADC without leveling 21% and with 98% leveling. Without leveling weighing resolution is 89 grm / bit and with 20 grm / bit leveling. Increased weighing resolution of 345%.
Energi angin merupakan salah satu sumber energy terbarukan yang memiliki potensi besar di Indonesia untuk dikembangkan sebagai pengganti energy fosil yang semakin menipis. Penggunaan energi angin sangat dipengaruhi kecepatan angin yang berfluktuasi sehingga menghasilkan tegangan keluaran yang berfluktuasi pula. Untuk mengatasi hal tersebut dibutuhkan baterai sebagai penyimpan energi. Pada artikel ini kan dibahas mengenai desain prototipe sistem konversi energi angin dengan menggunakan permanent magnet synchronous generator (PMSG) skala kecil yang terhubung ke baterai. Sistem didesain dengan menggunakan mikrokontroller sebagai pengolah data yang mengatur kerja sistem keseluruhan dan menghasilkan sinyal pulse width modulation (PWM) untuk konverter. Pada saat putaran angin dapat menghasilkan tenaga listrik yang baik maka tegangan untuk beban akan disuplai dari prototipe turbin angin tersebut. Namun jika tenaga listrik turbin angin yang dihasilkan kecil, maka tegangan untuk beban akan disuplai dari baterai. Berdasarkan hasil pengujian, rangkaian konverter dapat mengatur pengisian dan pengosongan baterai pada sistem turbin angin berdasarkan pengukuran arus dan tegangan
Resistance Temperatur Detector (RTD) atau dikenalsebagai detektor temperatur tahanan adalah sebuah alat yangdiginakan untuk menentukan nilai atau besaran suatutemperatur suhu dengan menggunakan elemen sensitif darikawat platina, tembaga, atau nikel murni, yang memberikannilai tahanan yang terbatas untuk masing-masing temperatur didalam kisaran suhunya. Pada pengukuran resistansi kabelRTD PT-100 memiliki berbagai macam metode. Ada 3 macammetode pengukuran yang dapat digunakan yaitu pengukuranresistansi kabel dengan 2 wire, 3 wire, dan 4 wire. Pengukuranresistansi ini digunakan pada industri yang memiliki jarakyang jauh antara sensor dengan kontrol. Antara sensor dengankontrol tersebut dihubungkan menggunakan kabel. Panjangpendeknya kabel mempengaruhi besar kecilnya nilairesistansi, semakin panjang kabel tersebut maka semakin besarnilai resistansi kabel. Pengaruh panas pada lingkungan sekitarkabel akan mempengaruhi nilai resistansi kabel yangakibatnya akan mempengaruhi hasil pengukuran RTD.Rangkaian untuk pengukuran resistansi menggunakanrangkaian jembatan Wheatstone. Rangkaian jembatanWheatstone tersusun dari empat buah hambatan. Pengukuranresistansi kabel 3 wire menggunakan rangkaian jembatanWheatstone lebih sering digunakan dari pada pengukuranresistansi kabel 2 wire, karena nilai resistansi 3 wire tidakmengalami perubahan atau kompensasi. Pada pengujian 3 wiredengan suhu 31 0C Vout pada 3 wire adalah 0,28 V dan padasuhu 76 0C Vout yang dihasilkan sebesar 0,29 V. Sedangkanpada 2 wire saat dipanaskan dengan suhu yang sama yaitu 310C menghasilkan Vout sebesar 0,27 V dan pada suhu 76 0CVout yang dihasilkan sebesar 0,98 V. Perbedaan yang sangatbesar ini mengakibatkan 3 wire lebih sering digunakan karenamenghasilkan nilai ΔV sebesar 0,01 V dari pada rangkaian 2wire yang menghasilkan nilai ΔV 0,71 V. Sehingga dengan 3wire menghasilkan hasil pengukuran yang lebih tepat.
The wind turbine system as a power plant is growing rapidly in line with the electrical energy needs and limitations of fossil energy as a source of electrical energy. Many research has been carried out to develop wind turbine systems and improve system efficiency. Research on wind turbine systems requires wind turbine emulators to simulate the behaviour of wind turbines against changes in wind speed. In this paper presents a design of speed controller based on PI controller for a Wind Turbine Emulator (WTE) using a Variable Speed Drive (VSD). WTE consists of VSD, microcontroller, 3 phase induction motor, Permanent Magnet Synchronous Generator (PMSG) and speed sensor. PMSG speed depends on wind speed. At certain wind speeds, PMSG will rotate at a certain value. WTE will adjust the speed of the induction motor according to a certain wind speed to drive PMSG. Motor and PMSG rotation speed are measured by rotary encoder sensor as speed sensor and feedback for WTE. Proportional-integral method is used to control the speed of a 3 phase induction motor through VSD analogue input. Based on experiment result, PI controller can adjust speed of induction motor so that PMSG will rotate according to a certain wind speed. WTE with PI controller controls the speed of induction motor at settling time 9s to simulate wind speed through PMSG speed controlling.
Bunga rosella di Indonesia dikonsumsi sebagai minuman teh herbal. Untuk memproses bunga rosella sebelum dikonsumsi, bunga rosella dipetik.kemudian.dikeringkan.di bawah sinar matahari. Namun pengeringan dengan menjemur.pada tempat terbuka di bawah sinar matahari membutuhkan.waktu cukup lama dua sampai tiga hari apabila musim hujan bisa mencapai tujuh hari. Untuk menyelesaikan permasalahan proses pengeringan bunga rosella secara konvensional, dapat dilakukan pengeringan menggunakan oven listrik dengan heater sebagai media pengering kelopak bunga rosella. Proses pengeringan rosella menggunakan oven listrik dengan mengatur suhu menggunakan kontrol PI yang diterapkan pada heater agar dapat mengatur tegangan keluaran pada heater dengan setpoint 60 o C. Metode ZN 1 dengan nilai Kp=9,49, dan Ki=0.02 didapatkan hasil pengujian suhu dengan performansi nilai td= 305 detik, tr= 904 detik, tp= 1268 detik, ts = 904 detik dan overshoot 1,67%. Proses penegeringan membutuhkan waktu yang lebih cepat selama 13 jam 30 menit dan menghasilkan berat akhir rosella 100gram. Kata Kunci : rosella, waktu, suhu, control PI I. PENDAHULUAN osella atau dengan nama latin Hisbicus Sabdariffa Linn merupakan tanaman dari keluarga jenis bunga sepatu yang berasal dari Afrika dan Timur Tengah. Tanaman perdu ini termasuk tanaman semusim, tingginya bisa mencapai 3,5 meter. Di Indonesia tanaman rosela ini banyak di gunakan sebagai minuman teh herbal. Tanaman rosela jika di tanam di Indonesia akan berbunga dan siap untuk di panen pada usia 5-6 bulan. Setelah rosela di panen biasanya tanaman kelopak bunga rosela di keringkan kemudian hasil kelopak bunga kering dikonsumsi dan kebanyakan diolah sebagai bahan untuk membuat minuman teh [1].
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.