To substantiate changes in stress-strain state of rock mass in the process of long-pillar mining with the help of double-unit longwalls while evaluating stress of a mine field in terms of Lvivvuhillia SE mine. Methods. Analysis of the plans of mine workings has become a basis for the evaluation of physical and geometrical parameters of a support pressure area of the double-unit stopes depending upon mining and geological as well as engineering conditions for n 7 b coal seam extraction. 3D model of the rock mass has been rendered using SolidWorks 2019 software. The geomechanical model of the rock mass is based upon the specified output data concerning actual operating schedule of 1018 and 1019 double-unit longwalls (numbers of the longwalls are changed as it has been required by the authorities of Lvivvuhillia SE) in terms of n 7 b seam and support patterns of the development mine workings in Lvivvuhillia SE mine. Each component of the support was modeled as a separate part with the relevant geotech data. Behaviour of the expansion of the rock mass stress-strain state within the selected point has been analyzed by means of sections at the specified plane. Findings. Rendering algorithm of 3D model of rock mass in terms of long-pillar mining of a coal seam using double-unit longwalls has been developed. A geomechanical model of the rock mass has been substantiated depending upon the mining and geological mode of occurrence and engineering parameters of coal mining process. Originality. Nature of the support pressure area formation in front of a stope as well as along the extraction pillar length has been analyzed. It has been identified that if stopes are within one and the same plane, interconnection of their frontal support pressure areas as well as walls of the development workings take place. In this context, adjoining entry acts as the extra destressing technogenic cavity in addition to its proper functions. Practical implications. Output data to make recommendations concerning the efficient mining parameters and methods for rock pressure control have been identified relying upon the analysis of stress-strain state of rock mass in the process of the operation of double-unit longwalls. Visualization of the principles of formation of the stress-strain state of support pressure area and evaluation of the rock mass condition have shown that the maximum reduced stresses reach 70 MPa in terms of 18 m width of the support pressure area.
The formation of the stress-strain state of rocks in the several phase gasification processes was considered. Proceeding from the well-known principles of thermodynamics and phase formation of the multi-type rockmass under the influence of the temperature field, a geomechanical model of a two-layer artificially-formed shell formed during the gasification process by the method of variation feeding of the blowing mixture to the body of the gas generator was developed. The Neumann principle is used for the magnitude determination of the maximum stress vector, which involves the definition of the axial tensor of mechanical deformations through the anisotropy of the thermal expansion (the polar tensor of the second rank). This makes the possibility to create the base for a package of information programs creation. Such programs give the possibility to simplify the study of the rockmass deformation characteristics and to evaluate the stresses in a thermally changing environment. Researches are carried out by creating the final element system with the adaptation to the specific mining-geological conditions. These approaches are checked both for working out the coal reserves and for utilization of the mining waste products. Results of this investigation were included to the Roman Dychkovskyi thesis of the scientific degree of the Doctor of the Technique Sciences “Scientific Principles of Technologies Combination for Coal Mining in Weakly Metamorphoses Rockmass”. They contain the researches, which were conducted within the project GP – 489, financed by Ministry of Education and Science of Ukraine.
Sometimes in mining, it is necessary to combine di erent extracting technologies within one enterprise. So, in this paper, the analysis of scienti c and technical mining operations with combined technologies is carried out, and the search for structure and their operation in the mining enterprise is performed. The processes and technological parameters of mineral extraction by two fundamentally di erent technologies are investigated in detail. Due to the introduction of additional technologies, it is possible to involve sub-standard reserves in the production process, and an algorithm for determining the technological parameters is developed. This algorithm consists of criteria that make it possible to nd compatibility in the work of one or more development technologies while maintaining an e ective level of extraction. To do this, all processes at the enterprise are grouped: by degree of exploration, feasibility and economic e ciency. For each of them, certain coe cients were determined on the example of the operation of two speci c combined technologies: the extraction of uranium ores and coal. For each group of criteria, certain coe cients are identi ed that allow assessing the feasibility of applying technology in their area. Their product is a general coe cient of compatibility, which shows the feasibility of introducing additional technology at the enterprise with the feasibility study. It de nes the amount of funds invested in the development of an enterprise to achieve e cient mineral extraction with combined technologies within one enterprise. This point can be used to predict the grade variability of stockpiles from the origin source and the methodology allows characterizing the iron grades within stockpiles without any extra sampling.
Purpose. The paper addresses the rock mass state estimation while excavating a cross-heading through the area of regional fault "Bohdanivskyi" based on probabilistic approach to assessing the rock strength.Methods. The boundaries and fault zone extension are specified based on geological service database. This hazardous fault area has been confirmed, and the expected water inflow and methane emission have been identified based on the probe holes drilled ahead of the advancing face. To assess the strength of rocks, the statistical strength theory is used. Numerical simulation is performed using finite element method that is well-tested in geomechanical problems. Findings.The technique of rock mass strength estimation using structural factor based on statistical strength theory has been implemented to improve the adequacy of mathematical modeling. Numerical simulation of geomechanical processes based on finite element method and Hoek-Brown failure criterion is carried out. The changes of rock stress-strain state while excavating the cross-heading through various sites of the fault zone are determined depending on the level of rock disintegration.Originality. New regularities of rock mass behavior within the fault area are determined based on developed technique of rock strength assessment considering the rock mass disintegration and watering.Practical implications. Estimation of rock failure has resulted in designing the combination of support systems comprising metal sets, rockbolts and shotcrete.
The paper represents the creation of the software simulation system, which reproduce the basic processes of mining and near production. It presents the consideration of such systems for both traditional and non-traditional mineral extraction systems. The principles of using computer recognition of processes are also presented in other processes of carbon-containing raw materials transition, as well as power production and waste utilization of mining production. These systems considerably expand the manageability of a rather complicated mining enterprise. The main purpose of such research is the simulation reproduction of all technological processors associated with the activity of mining enterprises on the display of the dispatch center. For this purpose, is used so-called UML-diagrams, which allows to simulate mining and near mining processes. Results of this investigation were included to the Roman Dychkovskyi thesis of the scientific degree of the Doctor of the Technique Sciences “Scientific Principles of Technologies Combination for Coal Mining in Weakly Metamorphoses Rockmass”.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.