Carotenoids and biodiesel from palm oil were recovered through a process involving neutralization and transesterification of palm oil followed by molecular distillation of the esters. The concentrated obtained contains more than 30,000 ppm of carotenoids and the distillate contains above 95% of light-colored biodiesel. The experimental data were obtained from falling film and centrifugal molecular distillators. It can be seen that each one has its own characteristics, which are a function of the operating temperatures and of the tendency of the material thermal decomposition. These characteristics can determine the type of equipment to be used, since they have different operating conditions. The experimental results were compared to the ones from simulations using the mathematical modeling for the falling film and centrifugal distillators developed.

DISMOL simulator was used to determine the best possible operating conditions to guide, in future studies, experimental works. This simulator needs several physical-chemical properties and often it is very difficult to determine them because of the complexity of the involved components. Their determinations must be made through correlations and/ or predictions, in order to characterize the system and calculate it. The first try is to have simulation results of a system that later can be validated with experimental data. To implement, in the simulator, the necessary parameters of complex systems is a difficult task. In this work, we aimed to determe these properties in order to evaluate the tocopherol (vitamin E) recovery using a DISMOL simulator. The raw material used was the crude deodorizer distillate of soya oil. With this procedure, it is possible to determine the best operating conditions for experimental works and to evaluate the process in the separation of new systems, analyzing the profiles obtained from these simulations for the falling film molecular distillator.

No abstract

In this work, important results from simulations are presented, showing the potentiality of the molecular distillation process for recovering vitamin E from vegetal oils. Two types of molecular distillators are considered: falling film and centrifugal. The results emphasize the degree of recovery and factors that influence substantially the performance of the molecular distillators, such as feed flow rate, residence time, and process temperature. Moreover, they show that each type of molecular distillator enables one to operate under specific residence time and temperature. Therefore, a careful analysis must be made in order to determine the best equipment and operating conditions for obtaining products with high quality and concentration, and reduced problems of material thermal decomposition. Vitamin E (tocopherols) from vegetal oils, more specifically, from the deodorizer distillate of soya oil, was the studied case.

An essentially predictive mathematical model was developed to simulate pervaporation process. The group contribution method UNIFAC was used for calculating the upstream activity coefficients. The diffusion coefficient in the membrane was predicted using free-volume theory. Free-volume parameters were determined with viscosity and temperature data, and the binary interaction solvent-polymer parameter was calculated by a group-contribution lattice-fluid equation of state (GCLF-EOS). A simulator named PERVAP was developed applying the mathematical model. Pervaporation process was simulated for separating bioethanol-water through polyetherimide membrane. The simulated results were validated using experimental data of bioethanol/water separation through polyetherimide membrane. The model presented a satisfactory performance compared to experimental data. Related to the simulation of the studied separation, a 99% molar enriched bioethanol stream was obtained with a recovery of 94%.

DISMOL simulator was used to determine the best possible operating conditions to guide, in future studies, experimental works. This simulator needs several physical-chemical properties and often it is very difficult to determine them because of the complexity of the involved components. Their determinations must be made through correlations and/or predictions, in order to characterize the system and calculate it. The first try is to have simulation results of a system that later can be validated with experimental data. To implement, in the simulator, the necessary parameters of complex systems is a difficult task. In this work, we aimed to determe these properties in order to evaluate the tocopherol (vitamin E) recovery using a DISMOL simulator. The raw material used was the crude deodorizer distillate of soya oil. With this procedure, it is possible to determine the best operating conditions for experimental works and to evaluate the process in the separation of new systems, analyzing the profiles obtained from these simulations for the falling film molecular distillator.

No abstract

In this article, the separation and the purification of the acrylic acid produced from renewable sugars were studied using the liquid-liquid extraction process. Nonrandom two-liquids and universal quasi-chemical models and the prediction method universal quasi-chemical functional activity coefficients were used for generating liquid-liquid equilibrium diagrams for systems made up of acrylic acid, water, and solvents (diisopropyl ether, isopropyl acetate, 2-ethyl hexanol, and methyl isobutyl ketone) and the results were compared with available liquid-liquid equilibrium experimental data. Aspen Plus (Aspen Technology, Inc., version 2004.1) software was used for equilibrium and process calculations. High concentration of acrylic acid was obtained in this article using diisopropyl ether as solvent.