Non-fullerene acceptors have recently attracted tremendous interest because of their potential as alternatives to fullerene derivatives in bulk heterojunction organic solar cells. However, the power conversion efficiencies (PCEs) have lagged far behind those of the polymer/fullerene system, mainly because of the low fill factor (FF) and photocurrent. Here we report a novel perylene bisimide (PBI) acceptor, SdiPBI-Se, in which selenium atoms were introduced into the perylene core. With a well-established wide-band-gap polymer (PDBT-T1) as the donor, a high efficiency of 8.4% with an unprecedented high FF of 70.2% is achieved for solution-processed non-fullerene organic solar cells. Efficient photon absorption, high and balanced charge carrier mobility, and ultrafast charge generation processes in PDBT-T1:SdiPBI-Se films account for the high photovoltaic performance. Our results suggest that non-fullerene acceptors have enormous potential to rival or even surpass the performance of their fullerene counterparts.

A novel perylene bisimide (PBI) dimer-based acceptor material, SdiPBI-S, was developed. Conventional bulk-heterojunction (BHJ) solar cells based on SdiPBI-S and the wide-band-gap polymer PDBT-T1 show a high power conversion efficiency (PCE) of 7.16% with a high open-circuit voltage of 0.90 V, a high short-circuit current density of 11.98 mA/cm(2), and an impressive fill factor of 66.1%. Favorable phase separation and balanced carrier mobilites in the BHJ films account for the high photovoltaic performance. The results demonstrate that fine-tuning of PBI-based materials is a promising way to improve the PCEs of non-fullerene BHJ organic solar cells.

Despite significant development recently, improving the power conversion efficiency of organic photovoltaics (OPVs) is still an ongoing challenge to overcome. One of the prerequisites to achieving this goal is to enable efficient charge separation and small voltage losses at the same time. In this work, a facile synthetic strategy is reported, where optoelectronic properties are delicately tuned by the introduction of electron-deficient-core-based fused structure into non-fullerene acceptors. Both devices exhibited a low voltage loss of 0.57 V and high short-circuit current density of 22.0 mA cm−2, resulting in high power conversion efficiencies of over 13.4%. These unconventional electron-deficient-core-based non-fullerene acceptors with near-infrared absorption lead to low non-radiative recombination losses in the resulting organic photovoltaics, contributing to a certified high power conversion efficiency of 12.6%.

Two kinds of conjugated C3-symmetric perylene dyes, namely, triperylene hexaimides (TPH) and selenium-annulated triperylene hexaimides (TPH-Se), are efficiently synthesized. Both TPH and TPH-Se have broad and strong absorption in the region 300-600 nm together with suitable LUMO levels of about -3.8 eV. Single-crystal X-ray diffraction studies show that TPH displays an extremely twisted three-bladed propeller configuration and a unique 3D network assembly in which three PBI subunits in one TPH molecule have strong π-π intermolecular interactions with PBI subunits in neighboring molecules. The integration of selenophene to TPH endows TPH-Se with a more distorted propeller configuration and a more compact 3D network assembly due to the Se···O interactions. A single-crystal transistor confirms that both TPH and TPH-Se possess good electron-transport ability. TPH and TPH-Se acceptor-based solar cells show high power conversion efficiency of 8.28% and 9.28%, respectively, which mainly results from the combined properties of broad and strong absorption ability, appropriate LUMO level, desirable aggregation, high electron mobility, and good film morphology with the polymer donor.

Effective management of the insulating ligands is prerequisite for achieving good electrical coupling between colloidal quantum dots (CQDs) and, thus, highperformance solar cells. Here, we developed a rationally designed post-synthetic process for effective control of ligand density on organic-inorganic hybrid formamidinium lead triiodide (FAPbI 3) perovskite CQDs. The resulting FAPbI 3 CQD solar cells demonstrated power-conversion efficiency of 8.38% with stability superior to that of bulk FAPbI 3 devices.

No abstract

The band edges of metal-halide perovskites with a general chemical structure of ABX3 (A, usually a monovalent organic cation; B, a divalent cation; and X, a halide anion) are constructed mainly of the orbitals from B and X sites. Hence, the structural and compositional varieties of the inorganic B–X framework are primarily responsible for regulating their electronic properties, whereas A-site cations are thought to only help stabilize the lattice and not to directly contribute to near-edge states. We report a π-conjugation–induced extension of electronic states of A-site cations that affects perovskite frontier orbitals. The π-conjugated pyrene-containing A-site cations electronically contribute to the surface band edges and influence the carrier dynamics, with a properly tailored intercalation distance between layers of the inorganic framework. The ethylammonium pyrene increased hole mobilities, improved power conversion efficiencies relative to that of a reference perovskite, and enhanced device stability.

Two different nonfullerene acceptors and one copolymer are used to fabricate ternary organic solar cells (OSCs). The two acceptors show unique interactions that reduce crystallinity and form a homogeneous mixed phase in the blend film, leading to a high efficiency of ≈10.3%, the highest performance reported for nonfullerene ternary blends. This work provides a new approach to fabricate high-performance OSCs.