Adhesives are made of polymers because, unlike other materials, polymers ensure good contact between surfaces by covering asperities, and retard the fracture of adhesive joints by dissipating energy under stress. But using polymers to 'glue' together polymer gels is difficult, requiring chemical reactions, heating, pH changes, ultraviolet irradiation or an electric field. Here we show that strong, rapid adhesion between two hydrogels can be achieved at room temperature by spreading a droplet of a nanoparticle solution on one gel's surface and then bringing the other gel into contact with it. The method relies on the nanoparticles' ability to adsorb onto polymer gels and to act as connectors between polymer chains, and on the ability of polymer chains to reorganize and dissipate energy under stress when adsorbed onto nanoparticles. We demonstrate this approach by pressing together pieces of hydrogels, for approximately 30 seconds, that have the same or different chemical properties or rigidities, using various solutions of silica nanoparticles, to achieve a strong bond. Furthermore, we show that carbon nanotubes and cellulose nanocrystals that do not bond hydrogels together become adhesive when their surface chemistry is modified. To illustrate the promise of the method for biological tissues, we also glued together two cut pieces of calf's liver using a solution of silica nanoparticles. As a rapid, simple and efficient way to assemble gels or tissues, this method is desirable for many emerging technological and medical applications such as microfluidics, actuation, tissue engineering and surgery.

pH-responsive gels of hydrophobically modified (HM) weak polyacid were prepared from acrylic acid and n-alkyl acrylates (n = 8, 12, 18). The HM gels obtained bear up to 20 mol % of n-alkyl acrylate units randomly distributed along the network chains. The pH-driven swelling of these gels upon ionization in an aqueous medium was studied. The effect of the fraction and of the side chain length of n-alkyl acrylate groups on the equilibrium degree of swelling was examined. It was shown that the swelling transition shifts to alkaline pH with increasing hydrophobicity of the gel. This was explained by the stabilization of the collapsed state of the gel by hydrophobic aggregation of n-alkyl side chains. The formation of such aggregates, which break down in the course of gel ionization, was confirmed by the fluorescent probe method with pyrene as a probe and by NMR spectroscopy. Potentiometric titration data of HM poly(acrylic acid) (PAA) gels and of the corresponding linear copolymers evidence that the introduction of hydrophobic repeat units only slightly affects the apparent dissociation constant of PAA, except for the most hydrophobic gels.

The synthesis and mechanical characterization of novel, tough poly(N,N-dimethylacrylamide) (PDMA)-silica hydrogel hybrids are presented to understand the role played by strong physical interactions between silica nanoparticles and the PDMA polymer on the properties of chemically cross-linked highly swollen PDMA networks. A detailed comparison of the hybrids with unmodified PDMA gels indicates that the incorporation of silica nanoparticles in the hydrogel increases the compression strength and the fracture toughness of notched samples up to an order of magnitude while increasing its modulus by a factor of 6 with a volume fraction of particles of the order of only 7%. The hybrid gels present a strain-dependent hysteresis but no permanent damage or residual strain upon unloading even after repeated cycling, a very unique property for such tough hydrogels. The reason for this exceptional increase in toughness is attributed mainly to the combined effect of breakable silica/polymer bonds and of a wide distribution of elastic chain lengths.

Sandcastle worms have developed protein‐based adhesives, which they use to construct protective tubes from sand grains and shell bits. A key element in the adhesive delivery is the formation of a fluidic complex coacervate phase. After delivery, the adhesive transforms into a solid upon an external trigger. In this work, a fully synthetic in situ setting adhesive based on complex coacervation is reported by mimicking the main features of the sandcastle worm's glue. The adhesive consists of oppositely charged polyelectrolytes grafted with thermoresponsive poly(N‐isopropylacrylamide) (PNIPAM) chains and starts out as a fluid complex coacervate that can be injected at room temperature. Upon increasing the temperature above the lower critical solution temperature of PNIPAM, the complex coacervate transitions into a nonflowing hydrogel while preserving its volume—the water content in the material stays constant. The adhesive functions in the presence of water and bonds to different surfaces regardless of their charge. This type of adhesive avoids many of the problems of current underwater adhesives and may be useful to bond biological tissues.

No abstract

We discovered that the free radical polymerization of N,N-dimethylacrylamide in water can lead, above a certain concentration, to gels without any added difunctional crosslinker. These so called ''selfcrosslinked'' hydrogels were prepared and their weak mechanical properties were improved by introducing silica nanoparticles. From swelling experiments performed at equilibrium in aqueous media, it was shown that silica particles behave as adhesive fillers and strongly interact with PDMA chains. These interactions are responsible for the reinforcement of mechanical properties. From initial elastic moduli, determined in the preparation state, we show that the elastic behaviour of these hydrogels mainly originates from entanglements and from physical crosslinks that can be controlled by the polymer concentration and the ratio between silica particles and polymer chains, respectively. The mechanical behaviour was characterized using: monotonic tensile tests, loading-unloading cycles at large strains and stress relaxation experiments in order to investigate long time behaviour. The introduction of silica highly increases the stiffness of the network without greatly reducing its extensibility, implying that strong interactions take place between PDMA chains and silica surfaces. Non-linear behavior was pointed out: softening at small deformations and hardening at high deformations which is related to finite chain extensibility. All these effects have been shown to strongly depend on the silica content. The analysis of hysteresis and residual strains induced by cycles, clearly indicate that contrary to chemical crosslinkers, hybrid interactions increase the dissipative process.Physico-chimie des Polym eres et des Milieux Dispers es, UMR 7615,

The strain rate effect on large strain dissipation and behavior recovery are presented to understand the toughening effect of silica nanoparticles in nanohybrid hydrogels. Such nanohybrid gels combine a poly(N,N-dimethylacrylamide) (PDMA) covalent network and physical interactions by adsorption of polymer chains at the silica nanoparticle surface. A series of model nanohybrid gels has been designed to obtain a well-controlled architecture. First insights on the structure (SANS) demonstrated that silica nanoparticles were welldispersed in the gel, including after cyclic mechanical loading. The characteristic times involved in the nanoparticle/polymer association were investigated by large strain mechanical cycling varying the strain rate from 3 × 10 −4 s −1 to 0.6 s −1 . The mechanical behavior of the hybrid hydrogel varies tremendously over a relatively small range of strain rates, ranging from almost non dissipative (at slow strain rates) to highly dissipative at high strain rates. However, upon cycling over time-scales of tens of seconds, the strong physical interactions taking place between nanosilica particles and PDMA network chains enabled the hydrogel to recover its initial mechanical properties. The main feature of this work is the remarkable role played by silica nanoparticles in the network to promote transient and recoverable connectivity by reversible adsorption/desorption processes. The strong strain rate dependence suggests that toughening mechanisms operating at standard strain rates as often reported, maybe quite different at slower or larger strain rates.

A novel mode of gel toughening displaying crack bifurcation is highlighted in phase-separated hydrogels. By exploring original covalent network topologies, phase-separated gels under isochoric conditions demonstrate advanced thermoresponsive mechanical properties: excellent fatigue resistance, self-healing, and remarkable fracture energies. Beyond the phase-transition temperature, the fracture proceeds by a systematic crack-bifurcation process, unreported so far in gels.