Numerous studies have reported the use of halide perovskites as highly functional light-harvesting materials. The development of optimized compositions and deposition approaches has led to impressive improvements; however, no noticeable breakthrough in performance has been observed for these materials recently. Here, a breakthrough that enables the fabrication of vertically grown halide perovskite (VGHP) nanopillar photodetectors via a nanoimprinting crystallization technique is demonstrated. We used engraved nanopatterned polymer stamps to form VGHP nanopillars during the pressurized crystallization of the softly baked gel state of a methylammonium lead iodide (CHNHPbI, denoted MAPI) film. The VGHP films exhibit much lower defect density and higher conductivity, as supported by current-voltage characteristic measurements and conductive atomic force microscopy measurements. Ultimately, two-terminal lateral photodetectors based on the VGHP nanopillar films show a greatly enhanced photoresponse compared with flat film-based photodetectors. We expect that the deposition method presented here will help surpass the technical limits and contribute to further improvements in various halide-perovskite-based devices.

Constructing a hierarchically porous structure in metal–organic frameworks (MOFs) can improve the accessibility of active sites and facilitate mass diffusion to enhance their adsorption and catalytic efficiency. Here, a novel linker competitive coordination strategy based on the electronegativity difference of two kinds of organic linkers is proposed to tailor the porous structure of Ti‐MOF (MIL‐125). A series of Ti‐MOFs with continuously tunable hierarchical porosity is obtained by simply adjusting the molar ratios of two organic linkers. The demonstration of toluene removal shows that the competitive coordination strategy not only contributes to wide pore size distribution to enhance the adsorption performance of toluene, but also endows good charge separation ability to facilitate photocatalytic performance. Finally, the toluene removal efficiency of optimal Ti‐MOF with mixed organic linkers of 1:1 molar ratio is 2.14 times and 1.88 times of the pristine MIL‐125 and MIL‐125(NH2), respectively. This strategy opens a new prospect to optimize Ti‐MOF properties for various heterogeneous catalysis applications.

In an attempt to replace thermally vulnerable organic perovskites, considerable research effort has recently been focused on the development of all‐inorganic perovskites in the field of photovoltaics. The preceding studies demonstrated that cesium lead halide perovskites are promising candidates for thermally stable and efficient solar cell materials. Here, the recent progress in cesium lead halide perovskite‐based solar cells is summarized. Whether organic cations are essential for the superiority of halide perovskites is controversial. However, more than 13% efficient solar cells have been successfully fabricated by employing cesium lead halide perovskites in a short amount of time. The state‐of‐the‐art materials engineering techniques will help to achieve a remarkable photovoltaic performance comparable to that of organic perovskites. In addition, improved understanding of the intrinsic photophysical behaviors will provide new insights that will facilitate further improvements in solar cell applications.

Even though poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) has been commonly used as a hole extraction layer (HEL) for p-i-n perovskite solar cells (PSCs), the cells' photovoltaic performance deteriorates because of the low and unstable work functions (WFs) of PEDOT:PSS versus those of a perovskite layer. To overcome this drawback, we synthesized a copolymer (P(SS- co-TFPMA)) ionomer consisting of PSS and tetrafluoropropylmethacrylate (TFPMA) as an alternative to conventional PEDOT:PSS. The PEDOT:P(SS- co-TFPMA) copolymer solution and its film exhibited excellent homogeneity and high phase stability compared with a physical mixture of TFPMA with PEDOT:PSS solution. During spin coating, a self-organized conducting PEDOT:P(SS- co-TFPMA) HEL evolved and the topmost PEDOT:P(SS- co-TFPMA) film showed a hydrophobic surface with a higher WF compared to that of the pristine PEDOT:PSS film because of its chemically bonded electron-withdrawing fluorinated functional groups. Interestingly, the WF of the conventional PEDOT:PSS film dramatically deteriorated after being coated with a perovskite layer, whereas the PEDOT:P(SS- co-TFPMA) film represented a relatively small influence. Because of the superior energy-level alignment between the HEL and a perovskite layer even after the contact, the open-circuit voltage, short-circuit current, and fill factor of the inverted planar p-i-n PSCs (IP-PSCs) with PEDOT:P(SS- co-TFPMA) were improved from 0.92 to 0.98 V, 18.96 to 19.66 mA/cm, and 78.96 to 82.43%, respectively, resulting in a 15% improvement in the power conversion efficiency vs that of IP-PSCs with conventional PEDOT:PSS. Moreover, the IP-PSCs with PEDOT:P(SS- co-TFPMA) layer showed not only improved photovoltaic performance but also enhanced device stability due to hydrophobic surface of PEDOT:P(SS- co-TFPMA) film.

Although organic–inorganic halide perovskite (OIHP)-based photovoltaics have high photoconversion efficiency (PCE), their poor humidity stability prevents commercialization. To overcome this critical hurdle, focusing on the grain boundary (GB) of OIHPs, which is the main humidity penetration channel, is crucial. Herein, pressure-induced crystallization of OIHP films prepared with controlled mold geometries is demonstrated as a GB-healing technique to obtain high moisture stability. When exposed to 85% RH at 30 °C, OIHP films fabricated by pressure-induced crystallization have enhanced moisture stability due to the enlarged OIHP grain size and low-angle GBs. The crystallographic and optical properties indicate the effect of applying pressure onto OIHP films in terms of moisture stability. The photovoltaic devices with pressure-induced crystallization exhibited dramatically stabilized performance and sustained over 0.95 normalized PCE after 200 h at 40% RH and 30 °C.