Two-dimensional (2D) semiconductors have been extensively explored as a new class of materials with great potential. In particular, black phosphorus (BP) has been considered to be a strong candidate for applications such as high-performance infrared photodetectors. However, the scalability of BP thin film is still a challenge, and its poor stability in the air has hampered the progress of the commercialization of BP devices. Herein, we report the use of hydrothermal-synthesized and air-stable 2D tellurene nanoflakes for broadband and ultrasensitive photodetection. The tellurene nanoflakes show high hole mobilities up to 458 cm2/V·s at ambient conditions, and the tellurene photodetector presents peak extrinsic responsivity of 383 A/W, 19.2 mA/W, and 18.9 mA/W at 520 nm, 1.55 μm, and 3.39 μm light wavelength, respectively. Because of the photogating effect, high gains up to 1.9 × 103 and 3.15 × 104 are obtained at 520 nm and 3.39 μm wavelength, respectively. At the communication wavelength of 1.55 μm, the tellurene photodetector exhibits an exceptionally high anisotropic behavior, and a large bandwidth of 37 MHz is obtained. The photodetection performance at different wavelength is further supported by the corresponding quantum molecular dynamics (QMD) simulations. Our approach has demonstrated the air-stable tellurene photodetectors that fully cover the short-wave infrared band with ultrafast photoresponse.

Red phosphorus offers a high theoretical sodium capacity and has been considered as a candidate anode for sodium-ion batteries. Similar to silicon anodes for lithium-ion batteries, the electrochemical performance of red phosphorus is plagued by the large volume variation upon sodiation. Here we perform in situ transmission electron microscopy analysis of the synthesized red-phosphorus-impregnated carbon nanofibers with the corresponding chemo-mechanical simulation, revealing that, the sodiated red phosphorus becomes softened with a “liquid-like” mechanical behaviour and gains superior malleability and deformability against pulverization. The encapsulation strategy of the synthesized red-phosphorus-impregnated carbon nanofibers has been proven to be an effective method to minimize the side reactions of red phosphorus in sodium-ion batteries, demonstrating stable electrochemical cycling. Our study provides a valid guide towards high-performance red-phosphorus-based anodes for sodium-ion batteries.

Fabrication of quantum dots (QDs) with emission covering a wide spectral region has been persistently intriguing because of their potentials in a range of practical applications such as biological labeling and imaging, solar cells, light-emitting diodes, and next-generation displays. In this work, we report the synthesis of CdZnSe–CdZnS core–shell alloy QDs through a Cu-catalyzed solid solution alloying strategy starting from CdSe–CdS core–shell QDs. The resulting CdZnSe–CdZnS alloy QDs exhibit emission profiles covering a wide wavelength range of 470–650 nm while maintaining high photoluminescence quantum yields. In addition, high morphological uniformity of the starting CdSe–CdS QDs can be largely retained in the final alloy QDs. We attribute this alloying process to the high mobility nature of Cu cations in Cd-chalcogenide crystals at elevated reaction temperatures, which allows Cu cations to act as transporting agents to transfer a Zn component into the CdSe–CdS QDs while maintaining the particle integrity. We show that this unique alloying strategy is independent of the shape of the starting QDs and can also be applied to the synthesis of CdZnSe–CdZnS nanorods. We anticipate that our study will instigate the synthesis of various high-quality alloy QDs and other alloy nanocrystals beyond what can be achieved currently.

Surface plasmons, collective electromagnetic excitations coupled to conduction electron oscillations, enable the manipulation of light–matter interactions at the nanoscale. Plasmon dispersion of metallic structures depends sensitively on their dimensionality and has been intensively studied for fundamental physics as well as applied technologies. Here, we report possible evidence for gate-tunable hybrid plasmons from the dimensionally mixed coupling between one-dimensional (1D) carbon nanotubes and two-dimensional (2D) graphene. In contrast to the carrier density-independent 1D Luttinger liquid plasmons in bare metallic carbon nanotubes, plasmon wavelengths in the 1D-2D heterostructure are modulated by 75% via electrostatic gating while retaining the high figures of merit of 1D plasmons. We propose a theoretical model to describe the electromagnetic interaction between plasmons in nanotubes and graphene, suggesting plasmon hybridization as a possible origin for the observed large plasmon modulation. The mixed-dimensional plasmonic heterostructures may enable diverse designs of tunable plasmonic nanodevices.

Developing convenient and accurate SARS-CoV-2 antigen test and serology test is crucial in curbing the global COVID-19 pandemic. In this work, we report an improved indium oxide (In 2 O 3 ) nanoribbon field-effect transistor (FET) biosensor platform detecting both SARS-CoV-2 antigen and antibody. Our FET biosensors, which were fabricated using a scalable and cost-efficient lithography-free process utilizing shadow masks, consist of an In 2 O 3 channel and a newly developed stable enzyme reporter. During the biosensing process, the phosphatase enzymatic reaction generated pH change of the solution, which was then detected and converted to electrical signal by our In 2 O 3 FETs. The biosensors applied phosphatase as enzyme reporter, which has a much better stability than the widely used urease in FET based biosensors. As proof-of-principle studies, we demonstrate the detection of SARS-CoV-2 spike protein in both phosphate-buffered saline (PBS) buffer and universal transport medium (UTM) (limit of detection [LoD]: 100 fg/mL). Following the SARS-CoV-2 antigen tests, we developed and characterized additional sensors aimed at SARS-CoV-2 IgG antibodies, which is important to trace past infection and vaccination. Our spike protein IgG antibody tests exhibit excellent detection limits in both PBS and human whole blood ((LoD): 1 pg/mL). Our biosensors display similar detection performance in different mediums, demonstrating that our biosensor approach is not limited by Debye screening from salts and can selectively detect biomarkers in physiological fluids. The newly selected enzyme for our platform performs much better performance and longer shelf life which will lead our biosensor platform to be capable for real clinical diagnosis usage. Electronic Supplementary Material Supplementary material (materials and methods for device fabrication, functionalization of In 2 O 3 devices, photographs of the liquid gate measurement setup, mobilities of the nine devices labeled in Fig. 1(b), family curves of I DS − V DS with the liquid gate setup and current change after bubbling the substrate solution (current vs. time curve for S1 antigen detection)) is available in the online version of this article at 10.1007/s12274-022-4190-0.

Orientation-controlled growth of two-dimensional (2D) transition metal dichalcogenides (TMDCs) may enable many new electronic and optical applications. However, previous studies reporting aligned growth of WSe 2 usually yielded very small domain sizes. Herein, we introduced gold vapor into the chemical vapor deposition (CVD) process as a catalyst to assist the growth of WSe 2 and successfully achieved highly aligned monolayer WSe 2 triangular flakes grown on c-plane sapphire with large domain sizes (130 μm) and fast growth rate (4.3 μm•s −1 ). When the aligned WSe 2 domains merged together, a continuous monolayer WSe 2 was formed with good uniformity. After transferring to Si/SiO 2 substrates, field effect transistors were fabricated on the continuous monolayer WSe 2 , and an average mobility of 12 cm 2 •V −1 •s −1 was achieved, demonstrating the good quality of the material. This report paves the way to study the effect of catalytic metal vapor in the CVD process of TMDCs and contributes a novel approach to realize the growth of aligned TMDC flakes.

Electron tunneling spectroscopy is a powerful technique to probe the unique physical properties of one-dimensional (1D) single-walled carbon nanotubes (SWNTs), such as the van Hove singularities in the density of states or the power-law tunneling probability of a Luttinger liquid. However, little is known about the tunneling behavior between two 1D SWNTs over a large energy spectrum. Here, we investigate the electron tunneling behavior between two crossed SWNTs across a wide spectral window up to 2 eV in the unique carbon nanotube-hexagonal boron nitride-carbon nanotube heterojunctions. We observe many sharp resonances in the differential tunneling conductance at different bias voltages applied between the SWNTs. These resonances can be attributed to elastic tunneling into the van Hove singularities of different 1D subbands in both SWNTs, and they allow us to determine the quasi-particle bandgaps and higher-lying 1D subbands in SWNTs on the insulating substrate.

Owing to the simplicity, scalability, and costefficiency, solution-processable two-dimensional (2D) semiconductors have attracted great interest in electronic applications, especially as the channel material for field-effect transistors (FETs). Inkjet printing is a lithography-free technique to achieve drop-on-demand patterning of solution-processable 2D ink. However, thus far, inkjet-printed 2D FETs exhibit limited performance due to the coffee-ring effect and consequent discontinuity of the printed 2D material films. Here, we report high-performance and flexible inkjet-printed MoS 2 FETs with high mobilities and high on/off ratios and their gas sensing applications. By preparing high-quality MoS 2 ink comprised of MoS 2 nanoplates using electrochemical exfoliation and then applying a binary solvent comprised of 2-butanol and isopropanol, the obtained ink was printed to form a continuous and relatively uniform MoS 2 film, and high-performance printed MoS 2 FETs were demonstrated, with mobilities of 11 cm 2 V −1 s −1 and on/off ratios of 10 6 . Furthermore, low-voltage gate modulation was achieved by applying an ion gel gate, and robust electrical performance under tensile strain was observed for the ion gel-gated MoS 2 FETs printed on flexible substrates. As the printed MoS 2 film is abundant in edge sites and sulfur vacancies, we further demonstrated our MoS 2 FETs as high-performance gas sensors with a limit of detection of 10 ppb for NO 2 and 0.5 ppm for NH 3 , together with a fast recovery rate.