The thermal conductivity increases linearly with bulk density q (60 q 120 kg/m 3 ).The isotherm sorption curves of straw bale are similar to wood. Young's modulus and Poisson's ratio depends on bulk density and bales orientation. A wall structure of 500 mm thickness has U-value between 0.1 and 0.2 W.m À2 .K À1 . Straw bale has less environmental impact compared to typical insulation materials.

High relative air humidity (RH ≥ 85%) during growth leads to stomata malfunctioning, resulting in water stress when plants are transferred to conditions of high evaporative demand. In this study, we hypothesized that an elevated air movement (MOV) 24 h per day, during the whole period of leaf development would increase abscisic acid concentration ([ABA]) enhancing stomatal functioning. Pot rose ‘Toril’ was grown at moderate (61%) or high (92%) RH combined with a continuous low (0.08 m s-1) or high (0.92 m s-1) MOV. High MOV reduced stomatal pore length and aperture in plants developed at high RH. Moreover, stomatal function improved when high MOV-treated plants were subjected to leaflet desiccation and ABA feeding. Endogenous concentration of ABA and its metabolites in the leaves was reduced by 35% in high RH, but contrary to our hypothesis this concentration was not significantly affected by high MOV. Interestingly, in detached leaflets grown at high RH, high MOV increased stomatal sensitivity to ABA since the amount of exogenous ABA required to decrease the transpiration rate was significantly reduced. This is the first study to show that high MOV increases stomatal functionality in leaves developed at high RH by reducing the stomatal pore length and aperture and enhancing stomatal sensitivity to ABA rather than increasing leaf [ABA].

No abstract

Climate change is anticipated to affect the degradation of the building materials in cultural heritage sites and buildings. For the aim of taking the necessary preventive measures, studies need to be carried out with the utmost possible precision regarding the building materials of each monument and the microclimate to which they are exposed. Within the present study, a methodology to investigate the mold risk of timber buildings is presented and applied in two historic constructions. The two case studies are located in Vestfold, Norway. Proper material properties are selected for the building elements by leveraging material properties from existing databases, measurements, and simulations of the hygrothermal performance of selected building components. Data from the REMO2015 driven by the global model MPI-ESM-LR are used in order to account for past, present, and future climate conditions. In addition, climate data from ERA5 reanalysis are used in order to assess the accuracy the MPI-ES-LR_REMO2015 model results. Whole building hygrothermal simulations are employed to calculate the temperature and the relative humidity on the timber surfaces. The transient hygrothermal condition and certain characteristics of the timber surfaces are used as inputs in the updated VTT mold model in order to predict the mold risk of certain building elements. Results show a significant increase of the mold risk of the untreated timber surfaces due to climate change. The treated surfaces have no mold risk at all. It is also observed that the most significant increase of the mold risk occurs in the north-oriented and the horizontal surfaces. It is underlined that the mold risk of the timber elements is overestimated by the MPI-ES-LR_REMO2015 model compared to ERA5 reanalysis. The importance of considering the surface temperature and humidity, and not the atmospheric temperature and humidity as boundary conditions in the mold growth model is also investigated and highlighted.

Wind-driven air infiltration has been recognized among the major reasons for energy loss in buildings, and the impact to energy efficiency under steady conditions has been reported and issued as part of many building codes. The nearly zero-energy building demand makes uncontrolled leakage paths even more undesired and creates the need for further investigation of their behavior under unsteady wind conditions. The present numerical study examines the role of wind gustiness on instantaneous infiltration rates of a low-rise building. For this purpose, two levels of gust frequency Ω have been simulated, expressed as a sinusoidal factor in the wind profile formula. In parallel, a ratio α is employed to represent seven different cases of external leakages distribution, while five scenarios of compartmentalization and internal leakages shows the impact of the latter on the dynamics of building air exchange rates. The results indicate that higher wind gustiness results in higher ACH, marking out gusts as a potential critical factor under unsteady climate conditions. The infiltration rates shown in relation to the leakage distribution ratio α provide arguments for the importance of the detailed detection of external leakages while the comparison of the different internal-volume-scenario highlights the key-role of internal leakages control towards a drastic reduction of infiltration rates.

No abstract

Bio-based building materials offer a wide range of outlooks, from traditional rustic to modern design products. Recent development in the science of materials significantly improves their functional performance. However, when considering the use of bio-materials in outdoor environments, materials will deteriorate due to processes like weathering, oxidation, biodegradation, wear, and decay. Consequentially, biomaterials may lose visual appeal, leading to a perceived need for replacement even if the material is far from reaching functional failure. Visual assessment is the most direct method for evaluation of the aesthetic appearance of materials. However, it possesses a high degree of subjectivity when performed by an untrained person. On the contrary, measurement of surface properties with dedicated sensors provides objective values that might be related to the current state of the material in use. Recent developments in field of optics and electronics opens a new possibility to perform measurements in-situ. Colour-, gloss-, or spectro-photo-meters allow non-destructive measurements without particular sample preparation. Since all of the above techniques provide complementary information, the multi-sensor approach is more frequently suggested for applied research. The material state can be assessed regularly during service life. In this case, such measurement turns into monitoring. The paper illustrates examples of assessment and monitoring of biomaterials' degradation due to weathering. Direct implementation of various sensors is demonstrated. A proposal for the approach of combining data provided by various sensing techniques with data mining is also presented.

Hygroscopic materials hold the potential to reduce ventilation loads in a building by damping the peak fluctuations of the indoor relative humidity. Of particular interest is the moisture buffer capacity of wooden surfaces. This paper investigates, the response of Norwegian spruce (Picea abies) samples to changes of indoor relative humidity as well as the corresponding latent heat release during moisture buffering. A climate chamber was used to subject samples to dynamic air humidity. Thermographic techniques and thermocouples were employed to measure surface temperature on the exposed surface of the spruce sample (permeable case), while a covered control sample was used as reference (impermeable case). The moisture uptake was logged synchronously by weighting cells. The results show that the surface temperature of spruce increased by 2.1°C during moisture uptake, while only by 0.9°C in the control sample. This finding has implications for direct energy savings when wooden surfaces are used indoors. In addition, thermography is evaluated as an appropriate measurement method for documenting latent heat release.