We present a new colloidal synthesis of gallium-doped zinc oxide nanocrystals that are transparent in the visible and absorb in the near-infrared. Thermal decomposition of zinc stearate and gallium nitrate after hot injection of the precursors in a mixture of organic amines leads to nanocrystals with tunable properties according to gallium amount. Substitutional Ga(3+) ions trigger a plasmonic resonance in the infrared region resulting from an increase in the free electrons concentration. These nanocrystals can be deposited by spin coating, drop casting, and spray coating resulting in homogeneous and high-quality thin films. The optical transmission of the Ga-ZnO nanoparticle assemblies in the visible is greater than 90%, and at the same time, the near-infrared absorption of the nanocrystals is maintained in the films as well. Several strategies to improve the films electrical and optical properties have been presented, such as UV treatments to remove the organic compounds responsible for the observed interparticle resistance and reducing atmosphere treatments on both colloidal solutions and thin films to increase the free carriers concentration, enhancing electrical conductivity and infrared absorption. The electrical resistance of the nanoparticle assemblies is about 30 kΩ/sq for the as-deposited, UV-exposed films, and it drops down to 300 Ω/sq after annealing in forming gas at 450 °C, comparable with state of the art tin-doped indium oxide coatings deposited from nanocrystal inks.

The performance of two types of radiello diffusive samplers, filled with a thermally desorbable adsorbent (graphitised carbon Carbograph 4) and with a solvent desorbable adsorbent (activated charcoal), respectively, have been evaluated for the monitoring of BTEX in ambient air, by comparison with active (pumped) samplers. A two year survey was carried out in Padua, a medium-sized town, in a traffic site, close to a busy crossroad. The concentrations of BTEX were measured for 15 campaigns, during which four series of radial diffusive samplers were exposed for 2 day, 7 day, 10 day and 14 day time periods, respectively. Every series of chemical desorption samplers included three replicates; thermal desorption samplers included six replicates, three of them filled with freshly conditioned cartridges and three filled with regenerated cartridges. No significant difference in the levels measured either by new or by regenerated cartridges has been found. During three campaigns (summer 2004, winter and spring 2005) two active (pumped) samplers were added for each sampling period. The diffusive uptake rates have been calculated and modelled under various conditions of concentration, temperature and exposure time. The effects of the environmental factors on the performances of both solvent and thermally desorbable samplers have been evaluated. The repeatability of the whole measurement process (sampling and analysis) was calculated for every sampling duration. The comparison of concentration levels measured by diffusive and active sampling methods shows correlation coefficients R >or= 0.98 (p<0.01) for all the compounds. The uncertainty of the diffusive sampling method under field conditions, using active sampling as the reference method, has been assessed according to the ISO 13752 requirements. On field relative expanded uncertainty for benzene has been found below 20%.

A diffusive sampling method for the determination of gaseous acetic and formic acids, using a radial symmetry diffusive sampler, has been optimised for a 7-day exposure time in this study. Sampling rate determinations were performed on data obtained from a dynamic exposure chamber, simulating the indoor conditions of an empty, closed, room, at room temperature and minimal wind speed. Analysis has been performed by means of ion chromatography. The sampling rates for formic acid concentrations of 128 microg m(-3) and 1248 microg m(-3) were determined to be 91.2 +/- 3.9 ml min(-1) and 111.6 +/- 2.8 ml min(-1), respectively. The acetic acid sampling rate was independent of the concentration in the range 160 microg m(-3)-1564 microg m(-3), and amounted to 97.3 +/- 3.1 ml min(-1). Experimentally determined sampling rates showed deviations of 3% for acetic acid, and 3-21% for formic acid, in relation to theoretically derived values. The blank values were as low as 1.69 +/- 0.07 microg for formic acid and 1.21 +/- 0.14 microg for acetic acid, and detection limits lower than 0.5 microg m(-3) could be achieved, which is an improvement of 98-99% compared to previously validated diffusive sampling methods. This study describes the first step of an extended validation program in which the applicability of these types of samplers for the measurement of organic acids will be validated and optimised for the environmental conditions typical for museum showcases.

2019. Validation of ammonia diffusive and pumped samplers in a controlled atmosphere test facility using traceable Primary Standard Gas Mixtures.