This study aimed to demonstrate the feasibility of hot-melt extrusion in the development of extended-release formulations of Fenbendazole (Fen) dispersed in PEO/PCL blend-based matrices. Their thermal, physical, chemical and viscosity properties were assessed by differential scanning calorimetry, thermogravimetric analysis/derivative thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffraction spectroscopy, and melt flow index. Drug dispersion was analyzed by scanning electron microscopy with electron dispersive X-ray spectroscopy, and drug release was evaluated by ultraviolet-visible spectroscopy. A thermal analysis indicated the conversion of the drug to its amorphous state. FTIR analysis endorsed the thermal studies pointing to a decrease in the drug’s crystallinity with the establishment of intermolecular interactions. XRD analysis confirmed the amorphous nature of Fen. MFI test revealed that PCL acts as a plasticizer when melt-processed with PEO. SEM images displayed irregular surfaces with voids and pores, while EDX spectra demonstrated a homogeneous drug distribution throughout the polymeric carrier. Dissolution testing revealed that PCL retards the drug release proportionally to the content of such polymer incorporated. These melt-extruded matrices showed that the drug release rate in a PEO/PCL blend can easily be tailored by altering the ratio of PCL to address the issues related to the multiple-dosing regimen of Fen in ruminants.
Four-dimensional printing is primarily based on the concept of 3D printing technology. However, it requires additional stimulus and stimulus-responsive materials. Poly-N-vinylcaprolactam is a temperature-sensitive polymer. Unique characteristics of poly-N-vinylcaprolactam -based hydrogels offer the possibility of employing them in 4D printing. The main aim of this study is to alter the phase transition temperature of poly-N-vinylcaprolactam hydrogels. This research focuses primarily on incorporating two additional monomers with poly-N-vinylcaprolactam: Vinylacetate and N-vinylpyrrolidone. This work contributes to this growing area of research by altering (increasing and decreasing) the lower critical solution temperature of N-vinylcaprolactam through photopolymerisation. Poly-N-vinylcaprolactam exhibits a lower critical solution temperature close to the physiological temperature range of 34–37 °C. The copolymers were analysed using various characterisation techniques, such as FTIR, DSC, and UV-spectrometry. The main findings show that the inclusion of N-vinylpyrrolidone into poly-N-vinylcaprolactam increased the lower critical solution temperature above the physiological temperature. By incorporating vinylacetate, the lower critical solution temperature dropped to 21 °C, allowing for potential self-assembly of 4D-printed objects at room temperature. In this case, altering the lower critical solution temperature of the material can potentially permit the transformation of the 4D-printed object at a particular temperature.
Poly (N-vinylcaprolactam) is a polymer that is biocompatible, water-soluble, thermally sensitive, non-toxic, and nonionic. In this study, the preparation of hydrogels based on Poly (N-vinylcaprolactam) with diethylene glycol diacrylate is presented. The N-Vinylcaprolactam-based hydrogels are synthesised by using a photopolymerisation technique using diethylene glycol diacrylate as a crosslinking agent, and Diphenyl (2, 4, 6-trimethylbenzoyl) phosphine oxide as a photoinitiator. The structure of the polymers is investigated via Attenuated Total Reflectance–Fourier Transform Infrared Spectroscopy. The polymers are further characterised using differential scanning calorimetry and swelling analysis. This study is conducted to determine the characteristics of P (N-vinylcaprolactam) with diethylene glycol diacrylate, including the addition of Vinylacetate or N-Vinylpyrrolidone, and to examine the effects on the phase transition. Although various methods of free-radical polymerisation have synthesised the homopolymer, this is the first study to report the synthesis of Poly (N-vinylcaprolactam) with diethylene glycol diacrylate by using free-radical photopolymerisation, using Diphenyl (2, 4, 6-trimethylbenzoyl) phosphine oxide to initiate the reaction. FTIR analysis shows that the NVCL-based copolymers are successfully polymerised through UV photopolymerisation. DSC analysis indicates that increasing the concentration of crosslinker results in a decrease in the glass transition temperature. Swelling analysis displays that the lower the concentration of crosslinker present in the hydrogel, the quicker the hydrogels reach their maximum swelling ratio.
Fenbendazole (FBZ) is a broad-spectrum anthelmintic administered orally to ruminants; nevertheless, its poor water solubility has been the main limitation to reaching satisfactory and sustained levels at the site of the target parasites. Hence, the exploitation of hot-melt extrusion (HME) and micro-injection moulding (µIM) for the manufacturing of extended-release tablets of plasticised solid dispersions of poly(ethylene oxide) (PEO)/polycaprolactone (PCL) and FBZ was investigated due to their unique suitability for semi-continuous manufacturing of pharmaceutical oral solid dosage forms. High-performance liquid chromatography (HPLC) analysis demonstrated a consistent and uniform drug content in the tablets. Thermal analysis using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) suggested the amorphous state of the active ingredient, which was endorsed by powder X-ray diffraction spectroscopy (pXRD). Fourier transform infrared spectroscopy (FTIR) analysis did not display any new peak indicative of either a chemical interaction or degradation. Scanning electron microscopy (SEM) images showed smoother surfaces and broader pores as we increased the PCL content. Electron-dispersive X-ray spectroscopy (EDX) revealed that the drug was homogeneously distributed within the polymeric matrices. Drug release studies attested that all moulded tablets of amorphous solid dispersions improved the drug solubility, with the PEO/PCL blend–based matrices showing drug release by Korsmeyer–Peppas kinetics. Thus, HME coupled with µIM proved to be a promising approach towards a continuous automated manufacturing process for the production of oral solid dispersions of benzimidazole anthelmintics to grazing cattle.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.