Characteristics of a new compact valve design for steam turbines are analysed by measuring pressure losses and oscillations on the valve model. It is the model of an intercept valve of the intermediate-pressure turbine part. This valve is relatively smaller hence cheaper than usual control and intercept valves. Besides, four different valve seat angles were tested in order to investigate the valve seat angle influence. In order to further clarify measured phenomena, the wide range of numerical simulations were also carried out. Measurements were performed in the Aerodynamic laboratory of the Institute of Thermomechanics of the Czech Academy of Sciences in an air test rig installed in a modular aerodynamic tunnel. Numerical simulations were performed in the Doosan Skoda Power Company using a package of ANSYS software tools. Measurement results are compared with numerical and generalized in the form of valve characteristics and pressure oscillation maps. As a result of the pressure loss analysis, pressure losses in similar valve assemblies can be predicted with required accuracy for each new turbine where modern compact valves are used. As a result of the pressure oscillation analysis, operating conditions at which dangerous flow instabilities can occur were identified. Thanks to this, the areas of safe and dangerous operating conditions can be predicted so that the operational reliability of the valve can be guaranteed.
A new design of an intercept valve assembly of the intermediate-pressure turbine part of greater power output is investigated in terms of pressure losses and flow fluctuations by using measurement on an experimental valve model. In addition, numerical simulations are used to further clarify measured phenomena. For such valve assemblies, it is important to exactly predict pressure losses and avoid danger of vibrations, which are caused by undesirable flow fluctuations, in order to guarantee valve’s efficiency and operational reliability. For this type of valve, it is especially important for turbine operations in partial loads (off-design conditions). Measurements were carried out in the Aerodynamic laboratory of the Institute of Thermomechanics of the Czech Academy of Sciences (IT) in a modular aerodynamic tunnel. Numerical simulations were carried out in the Doosan Skoda Power Company (DSP) by using a package of ANSYS software tools. The experimental valve model is a scaled model of a real valve assembly. It consists of an inlet pipeline, a stop valve and a control valve including its diffuser and outlet pipeline. Measured regimes were defined by a mass flow rate and a control valve cone lift which can be precisely changed. In order to investigate pressure loses, total and static pressures at valve characteristic locations were measured by using Prandtl probes and wall static pressure taps. In order to measure pressure fluctuations, Kulite fast response pressure transducers were used. They were situated near the valve throat where the flow fluctuations, which are strongly related to a flow separation, are the most visible and influential. Measurement results are compared with numerical results and locations with a flow separation were found. In order to reduce this phenomenon, different valve seat angles were also tested. As a result, a valve design could be optimized and, for a pressure loss prediction, a pressure loss model for this new intercept valve assembly could be created. Therefore, pressure losses in similar valve assemblies can be predicted with required accuracy for each new turbine where modern intercept valves are used. This helps to increase steam turbine efficiency and reduce fuel consumption. Based on pressure fluctuations results, operating conditions at which dangerous flow instabilities occur were identified. It was concluded that there is an operating condition border where the flow field starts to be unstable. As a result, the areas of safe and dangerous operating conditions can be predicted so that the operational reliability of the valve can be guaranteed.
The paper reports on interferometric measurements of flow over a NACA0015 airfoil model during flutter limit cycle oscillations. The airfoil model is fixed on an elastic support allowing motion with two degrees of freedom — pitch and plunge. The structural mass and stiffness matrices can be tuned to certain extent, so that the eigenfrequencies of the two modes approach as needed. The model is equipped with dynamic pressure probes and sensors measuring the airfoil vertical position. The flow field around the airfoil was measured by Mach-Zehnder interferometer and registered using a high-speed camera synchronously with the mechanical vibration and pressure measurements. The Mach number of the incident airflow was gradually increased and the response of the aeroelastic system to initial impulse measured, until the flutter instability onset occurred. Flutter boundaries were evaluated for various additional masses attached (i.e., for various plunging mode eigenfrequencies), and post-critical behavior of the system investigated. The interferograms recorded by the high-speed camera were postprocessed, yielding pressure distribution around the airfoil during its vibration and an estimate of the total aerodynamic force and energy transfer from the airflow to the structure.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.