There is a strong interest in the use of biopolymers in the electronic and biomedical industries, mainly towards low-cost applications. The possibility of developing entirely new kinds of products based on cellulose is of current interest, in order to enhance and to add new functionalities to conventional paper-based products. We present our results towards the development of paper-based microfluidics for molecular diagnostic testing. Paper properties were evaluated and compared to nitrocellulose, the most commonly used material in lateral flow and other rapid tests. Focusing on the use of paper as a substrate for microfluidic applications, through an eco-friendly wax-printing technology, we present three main and distinct colorimetric approaches: (i) enzymatic reactions (glucose detection); (ii) immunoassays (antibodies anti-Leishmania detection); (iii) nucleic acid sequence identification (Mycobacterium tuberculosis complex detection). Colorimetric glucose quantification was achieved through enzymatic reactions performed within specific zones of the paper-based device. The colouration achieved increased with growing glucose concentration and was highly homogeneous, covering all the surface of the paper reaction zones in a 3D sensor format. These devices showed a major advantage when compared to the 2D lateral flow glucose sensors, where some carryover of the coloured products usually occurs. The detection of anti-Leishmania antibodies in canine sera was conceptually achieved using a paper-based 96-well enzyme-linked immunosorbent assay format. However, optimization is still needed for this test, regarding the efficiency of the immobilization of antigens on the cellulose fibres. The detection of Mycobacterium tuberculosis nucleic acids integrated with a non-cross-linking gold nanoprobe detection scheme was also achieved in a wax-printed 384-well paper-based microplate, by the hybridization with a species-specific probe. The obtained results with the above-mentioned proof-of-concept sensors are thus promising towards the future development of simple and cost-effective paper-based diagnostic devices.

In this paper we employed phospholipid Langmuir monolayers as membrane models to probe interactions with chitosan. Using a combination of surface pressure--area and surface potential--area isotherms and rheological measurements with the pendent drop technique, we observed that chitosan interacts with phospholipid molecules at the air-water interface. We propose a model in which chitosan interacts with the phospholipids mainly through electrostatic interactions, but also including H-bonding and hydrophobic forces, depending on the phospholipid packing density. At large areas per molecule, chitosan in the subphase adsorbs onto the monolayer, expanding it. At small areas per molecule, chitosan is located in the subsurface. Indeed, a mixed chitosan-phospholipid monolayer can be transferred onto solid supports, even at high surface pressures. The effects of chitosan on the viscoelastic properties of phospholipid monolayers may be taken as evidence for the ability of chitosan to disrupt cell membranes.

The results of the search for the optimal experimental conditions for ultrasentitive chemical analysis of 1-naphthalenethiol (1-NAT) and 2-naphthalenethiol (2-NAT) using surface-enhanced Raman scattering (SERS) are discussed. The report begins with a review of the vibrational spectra, including infrared and Raman spectra of the target molecules, and the interpretation of the observed frequencies aided by local density functional theory (DFT) calculations at the B3LYP/6-311G(d,p) level of theory. Several metal nanostructures were tested for SERS activity, including island films and colloids of silver, gold and copper. Correspondingly, the most effective laser line for excitation in the visible and near infrared region was sought. The achieved detection limit for 1-naphthalenethiol, and for 2-naphthalenethiol, on silver nanostructures is in the zeptomole regime.

The interaction between chitosan and Langmuir and Langmuir-Blodgett (LB) films of dimyristoyl phosphatidic acid (DMPA) is investigated, with the films serving as simplified cell membrane models. At the air-water interface, chitosan modulates the structural properties of DMPA monolayers, causing expansion and decreasing the monolayer elasticity. As the surface pressure increased, some chitosan molecules remained at the interface, but others were expelled. Chitosan could be transferred onto solid supports alongside DMPA using the LB technique, as confirmed by infrared spectroscopy and quartz crystal microbalance measurements. The analysis of sum-frequency vibration spectroscopy data for the LB films combined with surface potential measurements for the monolayers pointed to chitosan inducing the ordering of the DMPA alkyl chains. Furthermore, the morphology of DMPA LB films, studied with atomic force microscopy, was affected significantly by the incorporation of chitosan, with the mixed chitosan-DMPA films displaying considerably higher thickness and roughness, in addition to chitosan aggregates. Because chitosan affected DMPA films even at pressures characteristic of cell membranes, we believe this study may help elucidate the role of chitosan in biological systems.

In this work, self-sustained, biocompatible, biodegradable films containing gold nanostructures have been fabricated for potential application in nanobioscience and ultrasensitive chemical and biochemical analysis. We report a novel synthesis of gold nanoparticles mediated by the biopolymer chitosan. Self-supporting thin films are formed from the resultant gold-chitosan nanocomposite solutions and characterized by UV-visible surface plasmon absorption, transmission electron microscopy, atomic force microscopy, infrared absorption, and Raman scattering measurements. Results demonstrate control over the size and distribution of the nanoparticles produced, which is promising for several applications, including the development of biosensors. As a proof of principle, we demonstrate that gold-chitosan films can be employed in trace analysis using surface-enhanced Raman scattering.

An artificial tongue composed of four sensors made from ultrathin films deposited onto gold interdigitated electrodes has been able to distinguish easily the four basic tastes (salty, sour, sweet, and bitter), in addition to detecting inorganic contaminants in ultrapure water and identifying different brands of coconut water. Some tastants were detected below the human threshold values, for example, 5 mM of NaCl or sucrose. Suppression of quinine by sucrose was also detected. The high sensitivity may be partially attributed to the ultrathin nature of the films as the sensors were produced with Langmuir−Blodgett films of the 16-mer polyaniline oligomer, polypyrrole, and a ruthenium complex and with self-assembled films of an azobenzene-containing polymer. The sensor response was evaluated with ac measurements taken at various frequencies, with the admittance being treated theoretically with an equivalent circuit representing the sensor immersed in a polyelectrolyte solution.

In this paper, the fabrication, characterization, and application of unique layer-by-layer (LBL) films of dendrimers and metallic nanoparticles is reported. Silver nanoparticles (d = approximately 20 nm) are produced in solution by sodium citrate reduction and incorporated into thin films with generation 1 and 5 DAB-Am dendrimers (polypropylenimine dendrimers with amino surface groups) by the LBL technique. The resulting nanocomposite films are characterized by UV-visible surface plasmon absorption and atomic force microscopy (AFM) measurements, and employed as substrates for surface-enhanced Raman scattering (SERS) of 2-naphthalenethiol. Through variation of the molecular size (dendrimer generation) and concentration of the cross-linker used, as well as the number of layers produced, the optical properties of several different possible architectures are studied. In the films, Ag nanoparticles are shown to be effectively immobilized and stabilized with increased control over their spacing and aggregation. Moreover, the films are shown to be excellent substrates for SERS measurements, demonstrating significant enhancement capability. As expected, large electromagnetic enhancement of Raman scattering signals is found to be strongly dependent on interparticle coupling between neighboring metallic nanoparticles. Finally, the possibility of detecting SERS signals from architectures with intervening layers between the metal nanoparticles and analyte molecules is explored. It is shown that although there are decreases in intensity with increasing number of intervening layers (as is expected from the distance dependence of SERS), electromagnetic enhancement is still able to function at these distances, thus offering the possibility of developing sensors with external layers that are chemically selective for specific analytes.

Tuberculosis (TB) remains one of the most serious infectious diseases in the world and the rate of new cases continues to increase. The development of cheap and simple methodologies capable of identifying TB causing agents belonging to the Mycobacterium tuberculosis Complex (MTBC), at point-of-need, in particular in resource-poor countries where the main TB epidemics are observed, is of paramount relevance for the timely and effective diagnosis and management of patients. TB molecular diagnostics, aimed at reducing the time of laboratory diagnostics from weeks to days, still require specialised technical personnel and labour intensive methods. Recent nanotechnology-based systems have been proposed to circumvent these limitations. Here, we report on a paper-based platform capable of integrating a previously developed Au-nanoprobe based MTBC detection assay-we call it "Gold on Paper". The Au-nanoprobe assay is processed and developed on a wax-printed microplate paper platform, allowing unequivocal identification of MTBC members and can be performed without specialised laboratory equipment. Upon integration of this Au-nanoprobe colorimetric assay onto the 384-microplate, differential colour scrutiny may be captured and analysed with a generic "smartphone" device. This strategy uses the mobile device to digitalise the intensity of the colour associated with each colorimetric assay, perform a Red Green Blue (RGB) analysis and transfer relevant information to an off-site lab, thus allowing for efficient diagnostics. Integration of the GPS location metadata of every test image may add a new dimension of information, allowing for real-time epidemiologic data on MTBC identification.