In TiO2-based dye-sensitized nanocrystalline solar cells, efficiencies of up to 11% have been obtained using Ru dyes, but the limited availability of these dyes together with their undesirable environmental impact have led to the search for cheaper and safer organic-based dyes. In this Letter, we report the synthesis, electronic, and photovoltaic properties of novel green porphyrin sensitizers. All six porphyrin dyes give solar cell efficiencies of ≥5%, but the best performing dye under standard global AM 1.5 solar conditions gives a short circuit photocurrent density (j sc) of 14.0 ± 0.20 mA/cm2, an open circuit voltage of 680 ± 30 mV, and a fill factor of 0.74, corresponding to an overall conversion efficiency of 7.1%, which, for porphyrin-based sensitizers, is unprecedented. This same dye gives an efficiency of 3.6% in a solid-state cell with spiro-MeOTAD as the hole transporting component, comparable to solid-state cells incorporating the best performing ruthenium dyes.

No abstract

A series of novel zinc metalloporphyrins, cyano-3-(2'-(5',10',15',20'-tetraphenylporphyrinato zinc(II))yl)-acrylic acid (Zn-3), 3-(trans-2'-(5',10',15',20'-tetraphenylporphyrinato zinc(II))yl)-acrylic acid (Zn-5), 2-cyano-5-(2'-(5',10',15',20'-tetraphenylporphyrinato zinc(II))yl)-penta-2,4-dienoic acid (Zn-8), 4-(trans-2'-(2' '-(5' ',10' ',15' ',20' '-tetraphenylporphyrinato zinc(II))yl)ethen-1'-yl))-1,2-benzenedicarboxylic acid (Zn-11), and 2-cyano-3-[4'-(trans-2' '-(2' ''-(5' '',10' '',15' '',20' ''-tetraphenylporphyrinato zinc(II))yl) ethen-1' '-yl)-phenyl]-acrylic acid (Zn-13) were synthesized and characterized by using various spectroscopic techniques. Density functional theory (DFT) and time-dependent DFT (TDDFT) calculations show that key molecular orbitals (MOs) of porphyrins Zn-5 and Zn-3 are stabilized and extended out onto the substituent by pi-conjugation, causing enhancement and red shifts of visible transitions and increasing the possibility of electron transfer from the substituent. The porphyrins were investigated for conversion of sunlight into electricity by constructing dye-sensitized TiO(2) solar cells using an I(-)/I(3)(-) electrolyte. The cells yield close to 85% incident photon-to-current efficiencies (IPCEs), and under standard AM 1.5 sunlight, the Zn-3-sensitized solar cell demonstrates a short circuit photocurrent density of 13.0 +/- 0.5 mA/cm(2), an open-circuit voltage of 610 +/- 50 mV, and a fill factor of 0.70 +/- 0.03. This corresponds to an overall conversion efficiency of 5.6%, making it the most efficient porphyrin-sensitized solar cell reported to date.

Negative carbon emission technologies are critical for ensuring a future stable climate. However, the gaseous state of CO 2 does render the indefinite storage of this greenhouse gas challenging. Herein, we created a liquid metal electrocatalyst that contains metallic elemental cerium nanoparticles, which facilitates the electrochemical reduction of CO 2 to layered solid carbonaceous species, at a low onset potential of −310 mV vs CO 2 /C. We exploited the formation of a cerium oxide catalyst at the liquid metal/electrolyte interface, which together with cerium nanoparticles, promoted the room temperature reduction of CO 2 . Due to the inhibition of van der Waals adhesion at the liquid interface, the electrode was remarkably resistant to deactivation via coking caused by solid carbonaceous species. The as-produced solid carbonaceous materials could be utilised for the fabrication of high-performance capacitor electrodes. Overall, this liquid metal enabled electrocatalytic process at room temperature may result in a viable negative emission technology.

No abstract

Conducting polymers (CPs) have exciting potential as scaffolds for tissue engineering, typically applied in regenerative medicine applications. In particular, the electrical properties of CPs has been shown to enhance nerve and muscle cell growth and regeneration. Hydrogels are particularly suitable candidates as scaffolds for tissue engineering because of their hydrated nature, their biocompatibility, and their tissue‐like mechanical properties. This study reports the development of the first single component CP hydrogel that is shown to combine both electro‐properties and hydrogel characteristics. Poly(3‐thiopheneacetic acid) hydrogels were fabricated by covalently crosslinking the polymer with 1,1′‐carbonyldiimidazole (CDI). Their swelling behavior was assessed and shown to display remarkable swelling capabilities (swelling ratios up to 850%). The mechanical properties of the networks were characterized as a function of the crosslinking density and were found to be comparable to those of muscle tissue. Hydrogels were found to be electroactive and conductive at physiological pH. Fibroblast and myoblast cells cultured on the hydrogel substrates were shown to adhere and proliferate. This is the first time that the potential of a single component CP hydrogel has been demonstrated for cell growth, opening the way for the development of new tissue engineering scaffolds.

No abstract

Porphyrin molecules offer immense potential as the light harvesting component of dye-sensitised nanocrystalline TiO(2) solar cells. Synthetic porphyrin dyes were amongst the first dyes trialled for sensitisation of inorganic semiconducting oxides. Today, they exhibit the best performance reported for dye-sensitised solar cells. Accompanying the significant performance improvement over the last two decades is a much improved understanding of efficiency-determining fundamental electron transfer steps, from charge photogeneration to recombination. In this feature article we highlight our recent discoveries of the influence of porphyrin molecule structure on efficiency determining electron transfer kinetics and device performance by systematically changing the molecular structure and observing electron injection and recombination kinetics using time-resolved optical and electrical probes. Despite our observation of ultrafast charge injection for all porphyrin dyes studied by transient absorption spectroscopy, the injection yield estimated using an internal standard remains below 100% and depends strongly on the molecular structure. The observed discrepancy between kinetic competition and the injection yield is attributed to non-injecting dyes, probably arising due to inhomogeneity. A very interesting sub-ns (0.5 ns to 100 ns) charge recombination channel between photo-injected electrons and porphyrin cations is observed, which is found to be more prominent in free-base porphyrin dyes with a conjugated linker. Charge recombination between the acceptor species in the redox containing electrolyte and injected electrons is shown to be an important limitation of most porphyrin-sensitised solar cells, accelerated by the presence of porphyrin molecules at the TiO(2)-electrolyte interface. This recombination reaction is strongly dependent on the porphyrin molecular structure. Bulky substituents, using a porphyrin dimer instead of a porphyrin monomer, a light soaking treatment of freshly prepared films and co-sensitization of TiO(2) with multiple dyes are shown to be successful strategies to improve electron lifetime. Finally, new developments unique to porphyrin dye-sensitised solar cells, including performance enhancements from a light exposure treatment of a zinc porphyrin dye, a significant performance improvement observed after co-sensitisation of TiO(2) with free-base and zinc porphyrin dyes and the use of porphyrin dimers with increased light harvesting in thin-film TiO(2) solar cells are described.