The prospect of using low cost, high throughput material deposition processes to fabricate organic circuitry and solar cells continues to drive research towards improving the performance of the semiconducting materials utilized in these devices. Conjugated aromatic polymers have emerged as a leading candidate semiconductor material class, due to their combination of their amenability to processing and reasonable electrical and optical performance. Challenges remain, however, to further improve the charge carrier mobility of the polymers for transistor applications and the power conversion efficiency for solar cells. This optimization requires a clear understanding of the relationship between molecular structure and both electronic properties and thin film morphology. In this Account, we describe an optimization process for a series of semiconducting polymers based on an electron rich indacenodithiophene aromatic backbone skeleton. We demonstrate the effect of bridging atoms, alkyl chain functionalization, and co-repeating units on the morphology, molecular orbital energy levels, charge carrier mobility, and solar cell efficiencies. This conjugated unit is extremely versatile with a coplanar aromatic ring structure, and the electron density can be manipulated by the choice of bridging group between the rings. The functionality of the bridging group also plays an important role in the polymer solubility, and out of plane aliphatic chains present in both the carbon and silicon bridge promote solubility. This particular polymer conformation, however, typically suppresses long range organization and crystallinity, which had been shown to strongly influence charge transport. In many cases, polymers exhibited both high solubility and excellent charge transport properties, even where there was no observable evidence of polymer crystallinity. The optical bandgap of the polymers can be tuned by the combination of the donating power of the bridging unit and the electron withdrawing nature of co-repeat units, alternating along the polymer backbone. Using strong donors and acceptors, we could shift the absorption into the near infrared.

A novel thiophene substituted isoindigo and its copolymer with benzothiadiazole have been synthesized. The polymer with low lying LUMO energy levels exhibits excellent ambipolar behavior in field effect transistors with both hole and electron mobilities recorded over 0.1 cm(2) V(-1) s(-1).

The synthesis of a new thieno[3,2‐b]thiophene isoindigo (iITT) based monomer unit, and its subsequent incorporation into a series of alternating copolymers is reported. Copolymerisation with benzothiadiazole, bithiophene and thiophene comonomer units by palladium catalysed cross coupling gives three new narrow band gap semiconducting polymers for OFET applications. Extending the fused nature of the isoindigo core serves to further enhance molecular orbital overlap along the polymer backbones and facilitate good charge transport characteristics thus demonstrating the potential of extending the fused ring system that is attached to the isoindigo core. When used as the semiconducting channel in top‐gate/bottom‐contact OFET devices, good ambipolar properties are observed, with hole and electron mobilities up to 0.4 cm2/Vs and 0.7 cm2/Vs respectively. The three new polymers show good stability, with high temperature annealing showing an increase in the crystallinity of the polymers which corresponds directly to charge carrier mobility improvement as shown by X‐ray diffraction, atomic force microscopy and photothermal deflection spectroscopy.

Current attempts to develop a proxy for Earth's surface ultraviolet-B (UV-B) flux focus on the organic chemistry of pollen and spores because their constituent biopolymer, sporopollenin, contains UV-B absorbing pigments whose relative abundance may respond to the ambient UV-B flux. Fourier transform infrared (FTIR) microspectroscopy provides a useful tool for rapidly determining the pigment content of spores. In this paper, we use FTIR to detect a chemical response of spore wall UV-B absorbing pigments that correspond with levels of shade beneath the canopy of a high-latitude Swedish birch forest. A 27% reduction in UV-B flux beneath the canopy leads to a significant (p<0.05) 7.3% reduction in concentration of UV-B absorbing compounds in sporopollenin. The field data from this natural flux gradient in UV-B further support our earlier work on sporopollenin-based proxies derived from sedimentary records and herbaria collections

The synthesis of a novel fused hexacyclic electron rich monomer incorporating thieno[3,2-b]thiophene is reported and characterized by single crystal X-ray diffraction. Suzuki co-polymerization with benzothiadiazole (BT) afforded a novel low band-gap polymer P4TBT with high molecular weights and good solution processability. Bulk heterojunction solar cell devices using the P4TBT and [70]PCBM gave power conversion efficiencies of 2.5%. Top-gate, bottom-contact field effect transistors (FETs) using P4TBT displayed high hole mobilities of 0.07 cm(2) · Vs(-1) demonstrating the suitability of the novel monomer and polymer for use in high performing organic electronic devices.

Typically a donor−acceptor (D−A) design strategy is used for engineering the bandgap of polymers for solar cells. However, in this work, a series of alternating D− A 1 −D−A 2 copolymers PnTQTI(F) were synthesized and characterized with oligothiophenes (nT, n = 1, 2, 3) as the donor and two electron-deficient moieties, quinoxaline and isoindigo, as the acceptors in the repeating unit. We have studied the influence of the donor segments with different numbers of thiophene units and the effect of the addition of fluorine to the quinoxaline unit of the D−A 1 −D−A 2 polymers. The photophysical, electrochemical, and photovoltaic properties of the polymers were examined via a range of techniques and related to theoretical simulations. On increasing the length of the donor thiophene units, broader absorption spectra were observed in addition to a sequential increase in HOMO levels, while the LUMO levels displayed very small variations. The addition of fluorine to the quinoxaline unit not only decreased the HOMO levels of the resulting polymers but also enhanced the absorption coefficients. A superior photovoltaic performance was observed for the P3TQTI-F-based device with a power conversion efficiency (PCE) of 7.0%, which is the highest efficiency for alternating D−A 1 −D−A 2 polymers reported to date. The structure−property correlations of the PnTQTI(F) polymers demonstrate that varying of the length of the donor segments is a valuable method for designing high-performance D−A 1 −D−A 2 copolymers and highlight the promising nature of D−A 1 −D−A 2 copolymers for efficient bulk-heterojunction solar cells.

Polymers based on quinoxaline and indacenodithieno[3,2-b]thiophene (IDTT) withmeta-hexyl-phenyl side chains were synthesized.

Two new conjugated polymers are synthesized based on a novel donor–acceptor–acceptor (D–A–A) design strategy with the intention of attaining lower lowest unoccupied molecular obital levels compared to the normally used D–A strategy. By coupling two thieno‐benzo‐isoindigo units together via the phenyl position to give a new symmetric benzene‐coupled di‐thieno‐benzo‐isoindigo (BdiTBI) monomer as an A–A acceptor and thiophene (T) or bithiophene (2T) as a donor, two new polymers PT‐BdiTBI and P2T‐BdiTBI are synthesized via Stille coupling. The two polymers are tested in top gate and top contact field effect transistors, which exhibit balanced ambipolar charge transport properties with poly(methyl methacrylate) as dielectric and a high hole mobility up to 1.1 cm2 V–1 s–1 with poly(trifluoroethylene) as dielectric. The polymer films are investigated using atomic force microscopy, which shows fibrous features due to their high crystallinity as indicated by grazing incidence wide‐angle X‐ray scattering. The theoretical calculations agree well with the experimental data on the energy levels. It is demonstrated that the D–A–A strategy is very effective for designing low band gap polymers for organic electronic applications.